Engine Oil Pan - Remove and Install
拆卸步骤
- 拆下放油塞 (1) 和 (2) 。 将发动机机油排入合适的容器以便保存或弃置。 有关正确的排放和加注步骤,请参阅操作和保养手册, "发动机机油和滤清器 - 更换"。 将 O 形密封圈从排放螺塞上拆下。
Show/hide table
图 1 | g02162853 |
- 拆下螺栓 (3) 后拆下油底壳 (4) 。
安装步骤
- 按与拆卸相反的顺序安装发动机油底壳 (4) 。
- 按照图 3 所示的顺序将螺栓 (3) 拧紧至扭矩为 40 ± 5 N·m (30 ± 7 lb ft)。
Show/hide table图 2 g02162853
Show/hide table图 3 g03524317
拧紧顺序
- 按照图 4 所示的顺序将螺栓 (3) 重新拧紧至扭矩为 47 ± 5 N·m (35 ± 4 lb ft)。
Show/hide table图 4 g03524498
重新拧紧的顺序
- 将放油塞 (1) 上紧到 70 ± 15 N·m (52 ± 11 lb ft) 的扭矩。
- 将放油塞 (2) 上紧到 90 ± 15 N·m (66 ± 11 lb ft) 的扭矩。
Caterpillar Information System:
C13, C15, and C18 Tier 4 Final Engines Water in Fuel - Test
C15 and C18 On-Highway Engines Camshaft - Remove and Install
C15 and C18 On-Highway Engines Camshaft - Remove and Install
3516C Marine Engine Model View Illustrations
2013/12/19 New Software Is Used on Certain C32 Marine Engines {1901, 1920}
Procedure for Installing the 450-6188 Solenoid Valve Gp and 450-3897 Wiring Harness on G3500 Petroleum Engines{5479} Procedure for Installing the 450-6188 Solenoid Valve Gp and 450-3897 Wiring Harness on G3500 Petroleum Engines{5479}
3516C Marine Engine Catalyst (SCR) - Replace
C280-16 Engine Exhaust Manifold Shield - Remove and Install
C15 and C18 On-Highway Engines Cylinder Head - Remove and Install
C15 and C18 On-Highway Engines Rocker Arm and Shaft - Remove and Install
Exhaust Leaks May Cause Failures of the 195-2431 Detonation Sensor Groups on Certain G3500 Engines{1408, 7400} Exhaust Leaks May Cause Failures of the 195-2431 Detonation Sensor Groups on Certain G3500 Engines{1408, 7400}
C15 and C18 On-Highway Engines Crankshaft Front Seal - Remove and Install
TA2 Technical Inspection for 3512B Dynamic Gas Blending Genset Engines{1000, 1050, 1250, 1300, 1350, 1400} TA2 Technical Inspection for 3512B Dynamic Gas Blending Genset Engines{1000, 1050, 1250, 1300, 1350, 1400}
2013/12/20 Improved Product Link Satellite System Special Instruction guide {7606}
C11 and C13 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Remove and Install
C15 and C18 On-Highway Engines Temperature Sensor (Cooled Exhaust Gas) - Remove and Install
C15 and C18 On-Highway Engines Engine Control Module - Remove and Install
C175 Oil Pressure Regulator Inspection and Rework{1304, 5117} C175 Oil Pressure Regulator Inspection and Rework{1304, 5117}
2014/03/31 A New Rear Engine Crankshaft Seal Is Now Used on Certain Excavators Equipped With C13 Engines {1161}
C280-16 Engine Alternator - Remove and Install
C280-08 Marine Engine Plate Locations and Film Locations
C4.4 Engines for Caterpillar Built Machines Crankshaft - Spheroidal Graphite Iron (SGI) Crankshaft
C4.4 Engines for Caterpillar Built Machines Connecting Rod Bearing Journal - Spheroidal Graphite Iron Crankshaft
C15 and C18 On-Highway Engines Vibration Damper and Pulley - Remove and Install