Rocker Arm and Shaft - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 124-2946     | 提升支架     | 1     |
开始:
- 拆下气门机构盖。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将螺柱 (1) 从摇臂轴组件 (2) 上拆下。
Show/hide table
图 1 | g01259735 |
Show/hide table
螺栓拆下之后,气门摇臂和单体喷油器摇臂应该可以在轴上移动。 从缸盖上拆下时,应保持轴水平。 为了避免可能的人身伤害,当把组件从缸盖上抬起时,保持手指远离气门摇臂和单体喷油器摇臂。 |
- 利用工具 (A) 拆下摇臂轴组件 (2) 。
Show/hide table
图 2 | g01262841 |
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 利用工具 (A) 安装摇臂轴组件 (2) 。
Show/hide table
图 3 | g01262841 |
- 将螺柱 (1) 安装到摇臂轴组件 (2) 上。 将螺柱上紧到 50 ± 5 N·m (37 ± 4 lb ft) 的扭矩。 将螺柱进一步转动 45 ± 5 度。
Show/hide table
图 4 | g01259735 |
Show/hide table
螺栓拆下之后,气门摇臂和单体喷油器摇臂应该可以在轴上移动。 从缸盖上拆下时,应保持轴水平。 为了避免可能的人身伤害,当把组件从缸盖上抬起时,保持手指远离气门摇臂和单体喷油器摇臂。 |
- 调整电子单体喷油器。 请参阅测试和调整, "电子单体喷油器 - 调整"。
- 调整发动机气门间隙。 请参阅测试和调整, "发动机气门间隙 - 检查/调整"。
End By: 安装气门机构盖。
Caterpillar Information System:
Exhaust Leaks May Cause Failures of the 195-2431 Detonation Sensor Groups on Certain G3500 Engines{1408, 7400} Exhaust Leaks May Cause Failures of the 195-2431 Detonation Sensor Groups on Certain G3500 Engines{1408, 7400}
C15 and C18 On-Highway Engines Crankshaft Front Seal - Remove and Install
C15 and C18 On-Highway Engines Power Take-Off Drive Group - Assemble
C15 and C18 On-Highway Engines Flywheel Housing - Remove and Install - Power Take Off equipped
C280 Marine Engines Battery
CX31-P600 Petroleum Transmission Hydraulic Oil Contamination - Test
C15 and C18 On-Highway Engines Flywheel - Remove and Install
CX31-P600 Petroleum Transmission Transmission Planetary Troubleshooting
C15 and C18 On-Highway Engines Water Temperature Regulator Housing - Remove and Install
CX31-P600 Petroleum Transmission Torque Converter Troubleshooting
CX31-P600 Petroleum Transmission Visual Inspection
C280-16 Engine Alternator - Replace
C15 and C18 On-Highway Engines Cylinder Head - Remove and Install
C280-16 Engine Exhaust Manifold Shield - Remove and Install
3516C Marine Engine Catalyst (SCR) - Replace
Procedure for Installing the 450-6188 Solenoid Valve Gp and 450-3897 Wiring Harness on G3500 Petroleum Engines{5479} Procedure for Installing the 450-6188 Solenoid Valve Gp and 450-3897 Wiring Harness on G3500 Petroleum Engines{5479}
2013/12/19 New Software Is Used on Certain C32 Marine Engines {1901, 1920}
3516C Marine Engine Model View Illustrations
C15 and C18 On-Highway Engines Camshaft - Remove and Install
C15 and C18 On-Highway Engines Camshaft - Remove and Install
C13, C15, and C18 Tier 4 Final Engines Water in Fuel - Test
C15 and C18 On-Highway Engines Engine Oil Pan - Remove and Install
TA2 Technical Inspection for 3512B Dynamic Gas Blending Genset Engines{1000, 1050, 1250, 1300, 1350, 1400} TA2 Technical Inspection for 3512B Dynamic Gas Blending Genset Engines{1000, 1050, 1250, 1300, 1350, 1400}
2013/12/20 Improved Product Link Satellite System Special Instruction guide {7606}