Vibration Damper and Pulley - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | -     | 导向螺柱 (5/8 - 18 x 9 in)     |
2     |
B     | -     | Loctite Graphite - 50 抗咬合润滑剂     |
-     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆下螺栓 (1) 和皮带轮 (2) 。
Show/hide table
图 1 | g03529480 |
- 拆下两个螺栓 (3) 。 安装工具 (A) 。
Show/hide table
图 2 | g03529479 |
- 拆下剩余的螺栓 (3) 。 拆下皮带轮 (4) 和减振器 (5) 。
安装步骤
Show/hide table
注意 |
---|
彻底接触粘滞减振器是否有漏油或外壳凹陷(损坏)的迹象。 这两个情况中的任何一个都可能导致重块与外壳相接触。 这样会影响粘滞减振器的操作。 |
- 按与拆卸相反的顺序安装减振器 (5) 。
- 将工具 (B) 涂抹在螺栓 (3) 上。
- 将螺栓 (3) 拧紧至扭矩为 90 ± 15 N·m (66 ± 11 lb ft),然后再转动 120 ±5 度。
Caterpillar Information System:
C4.4 Engines for Caterpillar Built Machines Connecting Rod Bearing Journal - Spheroidal Graphite Iron Crankshaft
C4.4 Engines for Caterpillar Built Machines Crankshaft - Spheroidal Graphite Iron (SGI) Crankshaft
C280-08 Marine Engine Plate Locations and Film Locations
C280-16 Engine Alternator - Remove and Install
2014/03/31 A New Rear Engine Crankshaft Seal Is Now Used on Certain Excavators Equipped With C13 Engines {1161}
C175 Oil Pressure Regulator Inspection and Rework{1304, 5117} C175 Oil Pressure Regulator Inspection and Rework{1304, 5117}
C15 and C18 On-Highway Engines Engine Control Module - Remove and Install
C15 and C18 On-Highway Engines Temperature Sensor (Cooled Exhaust Gas) - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Remove and Install
2013/12/20 Improved Product Link Satellite System Special Instruction guide {7606}
TA2 Technical Inspection for 3512B Dynamic Gas Blending Genset Engines{1000, 1050, 1250, 1300, 1350, 1400} TA2 Technical Inspection for 3512B Dynamic Gas Blending Genset Engines{1000, 1050, 1250, 1300, 1350, 1400}
C15 and C18 On-Highway Engines Engine Oil Pan - Remove and Install
C4.4 Engines for Caterpillar Built Machines Main Bearing Journal - Spheroidal Graphite Iron (SGI) Crankshaft
C4.4 Engines for Caterpillar Built Machines Connecting Rod - For Use With Spheroidal Graphite Iron (SGI) Crankshaft
C280-16 Engine Crankcase Explosion Relief Valve - Remove and Install
C15 and C18 On-Highway Engines Front Cover - Remove and Install
A Procedure Is Available to Adapt the Glow Plug Harness to Certain Engines{1403, 1412} A Procedure Is Available to Adapt the Glow Plug Harness to Certain Engines{1403, 1412}
C15 and C18 On-Highway Engines Pressure Sensor (Cooled Exhaust Gas) - Remove and Install - Differential Pressure
C11 and C13 On-Highway Engines Compression Brake Lash - Adjust
C15 and C18 On-Highway Engines Pressure Sensor (Cooled Exhaust Gas) - Remove and Install - Outlet Pressure
C15 and C18 On-Highway Engines Boost Pressure Sensor - Remove and Install
C15 and C18 On-Highway Engines Inlet Air Temperature Sensor - Remove and Install
C15 and C18 On-Highway Engines Belt Tensioner - Remove and Install - Fan Belt Tensioner
Exhaust Balance Valve Causing Regeneration Issues On Certain Tier 4i C13 Engines{1061, 5479} Exhaust Balance Valve Causing Regeneration Issues On Certain Tier 4i C13 Engines{1061, 5479}