Crankshaft Front Seal - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 1U-7600     | 滑锤拉拔器     | 1     |
B     | 5P-1733     | 密封定位器     | 1     |
C     | 5P-1737     | 螺栓     | 3     |
D     | 9S-8858     | 螺母 (密封件安装工具)     | 1     |
E     | 6V-6142     | 油封安装工具     | 1     |
开始:
- 拆下减振器和皮带轮。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 必要时,利用工具 (A) 或冲头以及手锤在耐磨衬套 (1) 内冲出三个或更多小孔。
Show/hide table
图 1 | g01255652 |
- 必要时,利用工具 (A) 拆下耐磨衬套 (1) 。
- 使用工具 (A) 或者冲头和锤子在曲轴前油封 (2) 上冲出不少于三个的孔。
- 使用工具 (A) 拆下曲轴前油封 (2) 。
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 在安装曲轴前密封和承磨衬套之前,请检查曲轴有无划痕。 此外,请检查曲轴表面是否有无可能引起失圆状况的变形。 使用抛光布以清除曲轴上的瑕疵。
注: 在安装曲轴前密封和承磨衬套的过程中,请勿使用任何类型的润滑剂。
- 清洁曲轴外径。
- 利用工具 (C) 将工具 (B) 固定到曲轴上。
Show/hide table
图 2 | g01255654 |
- 将耐磨衬套 (2) 和曲轴前密封 (1) 作为一体安装到工具 (B) 上。 将工具 (E) 安装到工具 (B) 上。 润滑工具 (D) 上的垫圈表面。 将工具 (D) 安装到工具 (B) 上。
注: 把曲轴前密封安装到发动机中,并使指示曲轴转动方向的箭头指向发动机前方。
- 拧紧工具 (D) ,直到工具 (E) 接触到工具 (B) 。
- 将工具 (D) 和工具 (E) 从工具 (B) 上拆下。
- 将工具 (C) 和工具 (B) 从曲轴上拆下。
End By: 安装减振器和皮带轮。
Caterpillar Information System:
C15 and C18 On-Highway Engines Power Take-Off Drive Group - Assemble
C15 and C18 On-Highway Engines Flywheel Housing - Remove and Install - Power Take Off equipped
C280 Marine Engines Battery
CX31-P600 Petroleum Transmission Hydraulic Oil Contamination - Test
C15 and C18 On-Highway Engines Flywheel - Remove and Install
CX31-P600 Petroleum Transmission Transmission Planetary Troubleshooting
C15 and C18 On-Highway Engines Water Temperature Regulator Housing - Remove and Install
CX31-P600 Petroleum Transmission Torque Converter Troubleshooting
CX31-P600 Petroleum Transmission Visual Inspection
C280-16 Engine Alternator - Replace
2014/02/20 New Anti Drift Valves are Now Used on Certain 345D and 349D Excavators {5059}
C15 and C18 On-Highway Engines Engine Oil Pump - Remove and Install
Exhaust Leaks May Cause Failures of the 195-2431 Detonation Sensor Groups on Certain G3500 Engines{1408, 7400} Exhaust Leaks May Cause Failures of the 195-2431 Detonation Sensor Groups on Certain G3500 Engines{1408, 7400}
C15 and C18 On-Highway Engines Rocker Arm and Shaft - Remove and Install
C15 and C18 On-Highway Engines Cylinder Head - Remove and Install
C280-16 Engine Exhaust Manifold Shield - Remove and Install
3516C Marine Engine Catalyst (SCR) - Replace
Procedure for Installing the 450-6188 Solenoid Valve Gp and 450-3897 Wiring Harness on G3500 Petroleum Engines{5479} Procedure for Installing the 450-6188 Solenoid Valve Gp and 450-3897 Wiring Harness on G3500 Petroleum Engines{5479}
2013/12/19 New Software Is Used on Certain C32 Marine Engines {1901, 1920}
3516C Marine Engine Model View Illustrations
C15 and C18 On-Highway Engines Camshaft - Remove and Install
C15 and C18 On-Highway Engines Camshaft - Remove and Install
C13, C15, and C18 Tier 4 Final Engines Water in Fuel - Test
C15 and C18 On-Highway Engines Engine Oil Pan - Remove and Install