Model View Illustrations
Show/hide table
Illustration 1 | g02856099 |
View of the right side of a typical 3500 C Marine Engine (1) Exhaust outlet (2) Heat shield for the turbochargers and for the exhaust outlet elbow (3) Exhaust bypass valve (4) Fumes disposal filters (5) Engine crankcase breathers (6) Heat shield for the aftercoolers (7) Engine oil filter (8) Fuel filter (9) Expansion tank (10) Engine oil sampling valve (11) Engine oil pump (12) Engine oil cooler (13) Engine oil level gauge (14) Power distribution box (15) Engine air cleaner |
Show/hide table
Illustration 2 | g02856101 |
View of the left side of a typical 3500 C Marine Engine (16) Filler cap for the expansion tank (17) Cover for the electronic control module (ECM) (18) Water temperature regulator (19) Water pump (20) Auxiliary water pump (21) Cover group for the ECM |
Show/hide table
Illustration 3 | g02963039 |
View of the rear of a typical 3500 C Marine Engine (22) Turbochargers |
Show/hide table
Illustration 4 | g03470978 |
Dosing Control Cabinet (1) Service tool connector (2) Electrical harness connection to engine ECM (3) Electrical harness connection to DEF tank (4) Electrical harness connection from CEM to dosing cabinet (5) DEF vent port (6) 120 V AC source (7) DEF outlet to CEM (8) DEF inlet/strainer (9) Air outlet to CEM (10) Air inlet/strainer |
Show/hide table
Illustration 5 | g03523614 |
U-Flow Reactor Housing (1) Outlet spool (2) DEF injector (3) Inlet spool (4) Inlet sensor box (5) Lifting eyes (6) Catalyst access cover (7) Outlet sensor box (8) Mounting brackets |
Show/hide table
Illustration 6 | g03535445 |
Z-Flow Reactor Housing (1) Outlet spool (2) DEF injector (3) Inlet spool (4) Inlet sensor box (5) Lifting eyes (6) Catalyst access cover (7) Outlet sensor box (8) Mounting brackets |
Caterpillar Information System:
2013/12/19 New Software Is Used on Certain C32 Marine Engines {1901, 1920}
Procedure for Installing the 450-6188 Solenoid Valve Gp and 450-3897 Wiring Harness on G3500 Petroleum Engines{5479} Procedure for Installing the 450-6188 Solenoid Valve Gp and 450-3897 Wiring Harness on G3500 Petroleum Engines{5479}
3516C Marine Engine Catalyst (SCR) - Replace
C280-16 Engine Exhaust Manifold Shield - Remove and Install
C15 and C18 On-Highway Engines Cylinder Head - Remove and Install
C15 and C18 On-Highway Engines Rocker Arm and Shaft - Remove and Install
Exhaust Leaks May Cause Failures of the 195-2431 Detonation Sensor Groups on Certain G3500 Engines{1408, 7400} Exhaust Leaks May Cause Failures of the 195-2431 Detonation Sensor Groups on Certain G3500 Engines{1408, 7400}
C15 and C18 On-Highway Engines Crankshaft Front Seal - Remove and Install
C15 and C18 On-Highway Engines Power Take-Off Drive Group - Assemble
C15 and C18 On-Highway Engines Flywheel Housing - Remove and Install - Power Take Off equipped
C280 Marine Engines Battery
CX31-P600 Petroleum Transmission Hydraulic Oil Contamination - Test
C15 and C18 On-Highway Engines Camshaft - Remove and Install
C15 and C18 On-Highway Engines Camshaft - Remove and Install
C13, C15, and C18 Tier 4 Final Engines Water in Fuel - Test
C15 and C18 On-Highway Engines Engine Oil Pan - Remove and Install
TA2 Technical Inspection for 3512B Dynamic Gas Blending Genset Engines{1000, 1050, 1250, 1300, 1350, 1400} TA2 Technical Inspection for 3512B Dynamic Gas Blending Genset Engines{1000, 1050, 1250, 1300, 1350, 1400}
2013/12/20 Improved Product Link Satellite System Special Instruction guide {7606}
C11 and C13 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Remove and Install
C15 and C18 On-Highway Engines Temperature Sensor (Cooled Exhaust Gas) - Remove and Install
C15 and C18 On-Highway Engines Engine Control Module - Remove and Install
C175 Oil Pressure Regulator Inspection and Rework{1304, 5117} C175 Oil Pressure Regulator Inspection and Rework{1304, 5117}
2014/03/31 A New Rear Engine Crankshaft Seal Is Now Used on Certain Excavators Equipped With C13 Engines {1161}
C280-16 Engine Alternator - Remove and Install