Engine Control Module - Remove and Install
拆卸步骤
- 断开蓄电池。 请参阅操作和保养手册, "蓄电池或蓄电池电缆 - 断开"。
- 拆下螺母 (1) 。
Show/hide table
图 1 | g02103128 |
- 松开内六角螺栓 (2) 后将线束组件放到一旁。
- 断开软管组件 (4) 和 (5) 。
- 拆下螺柱 (3) 。 拆下发动机控制模块、垫圈和隔离安装件。
安装步骤
- 按与拆卸相反的顺序安装发动机控制模块。
- 将内六角螺栓 (2) 上紧到 6 ± 1 N·m (53 ± 9 lb in) 的扭矩。
Caterpillar Information System:
C15 and C18 On-Highway Engines Temperature Sensor (Cooled Exhaust Gas) - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Valve Actuator (Variable) - Remove and Install
2013/12/20 Improved Product Link Satellite System Special Instruction guide {7606}
TA2 Technical Inspection for 3512B Dynamic Gas Blending Genset Engines{1000, 1050, 1250, 1300, 1350, 1400} TA2 Technical Inspection for 3512B Dynamic Gas Blending Genset Engines{1000, 1050, 1250, 1300, 1350, 1400}
C15 and C18 On-Highway Engines Engine Oil Pan - Remove and Install
C13, C15, and C18 Tier 4 Final Engines Water in Fuel - Test
C15 and C18 On-Highway Engines Camshaft - Remove and Install
C15 and C18 On-Highway Engines Camshaft - Remove and Install
3516C Marine Engine Model View Illustrations
2013/12/19 New Software Is Used on Certain C32 Marine Engines {1901, 1920}
Procedure for Installing the 450-6188 Solenoid Valve Gp and 450-3897 Wiring Harness on G3500 Petroleum Engines{5479} Procedure for Installing the 450-6188 Solenoid Valve Gp and 450-3897 Wiring Harness on G3500 Petroleum Engines{5479}
3516C Marine Engine Catalyst (SCR) - Replace
C175 Oil Pressure Regulator Inspection and Rework{1304, 5117} C175 Oil Pressure Regulator Inspection and Rework{1304, 5117}
2014/03/31 A New Rear Engine Crankshaft Seal Is Now Used on Certain Excavators Equipped With C13 Engines {1161}
C280-16 Engine Alternator - Remove and Install
C280-08 Marine Engine Plate Locations and Film Locations
C4.4 Engines for Caterpillar Built Machines Crankshaft - Spheroidal Graphite Iron (SGI) Crankshaft
C4.4 Engines for Caterpillar Built Machines Connecting Rod Bearing Journal - Spheroidal Graphite Iron Crankshaft
C15 and C18 On-Highway Engines Vibration Damper and Pulley - Remove and Install
C4.4 Engines for Caterpillar Built Machines Main Bearing Journal - Spheroidal Graphite Iron (SGI) Crankshaft
C4.4 Engines for Caterpillar Built Machines Connecting Rod - For Use With Spheroidal Graphite Iron (SGI) Crankshaft
C280-16 Engine Crankcase Explosion Relief Valve - Remove and Install
C15 and C18 On-Highway Engines Front Cover - Remove and Install
A Procedure Is Available to Adapt the Glow Plug Harness to Certain Engines{1403, 1412} A Procedure Is Available to Adapt the Glow Plug Harness to Certain Engines{1403, 1412}