Final Drive
Show/hide table
图 1 | g01801814 |
注: 组装前,将 4C-4030 螺纹锁固胶 涂抹在螺栓螺纹上。
(1) 28 只螺栓的扭矩 ... 1800 ± 200 N·m (1320 ± 150 lb ft)
(2) 2 只管塞的扭矩 ... 80 ± 10 N·m (60 ± 7 lb ft)
(3) 组装前,将 4C-4030 螺纹锁固胶 涂抹在 12 个螺栓螺纹上。
(4) 组装前,将 4C-5599 防咬合剂 涂抹在 6 个定位销配件的内径和外径上。
(5) 组装时,必须清洁和干燥橡胶曲面密封圈和与密封圈接触的所有表面。 安装前,在金属密封的接触表面上涂抹一薄层 6V-4876 润滑剂 。 该密封的组装必须与孔相符。 胶曲面密封圈不得有凸起。 不得扭曲胶曲面密封圈。
(6) 根据需要,使用 7Y-0808 垫片 来调整盖和齿圈之间的间隙 (C) :
-
(C) 间隙 ... 1.0 至 2.6 mm (0.04
至 0.10 in)
- 数量 ... 1
- 垫片厚度 ... 1.6 (0.06 in)
(7) 将 4C-5599 防咬合剂 涂抹在 2 个专用圆锥滚柱轴承内环的内径和外径上。
(8) 将 4C-5599 防咬合剂 涂抹在 2 个专用圆锥滚柱轴承外环的内径和外径上。
(9) 组装前,将 4C-4030 螺纹锁固胶 涂抹在两个内六角头调整螺钉的螺纹上。 安装内六角头调整螺钉,需与盖表面平齐。
(10) 组装前,将 1U-8846 垫片密封胶 涂抹到齿圈的表面上。
注: 使用下列步骤调整轴承的预加载荷:
- 在专用圆锥滚柱轴承内环上放置 10000 kg (22050 lb) 重的负载 (13) 。
- 转动壳体 (14) 以落座锁定轴承。
- 将负载 (13) 降低至 3700 ± 370 kg (8160 ± 815 lb)。
- 测量马达壳体顶面和轴承内环之间的距离 (G) 。
- 测量连接器齿轮 (11) 的步长 (F) 。
- 根据需要,使用垫片 (12) ,以便在锁定轴承和连接齿轮 (11) 之间获得正确的间隙。 使用下表 1 计算垫片的总厚度:
Show/hide table
表 1 测量值     公差     (G) − (F)    
± 0.10 mm (± 0.004 in)    
注: 如果需 2 片垫片 (12) ,则靠近连接器齿轮处安装最薄的垫片。
(12) 垫片
-
136-2959 垫片
- 数量 ... 1
- 垫片厚度 ... 0.30 ± 0.04 mm (0.012 ± 0.002 in)
-
136-2962 垫片
- 数量 ... 1
- 垫片厚度 ... 0.60 ± 0.06 mm (0.024 ± 0.002 in)
-
136-2963 垫片
- 数量 ... 1
- 垫片厚度 ... 0.70 ± 0.06 mm (0.028 ± 0.002 in)
-
136-2964 垫片
- 数量 ... 1
- 垫片厚度 ... 0.80 ± 0.07 mm (0.031 ± 0.003 in)
-
136-2965 垫片
- 数量 ... 1
- 垫片厚度 ... 1.00 ± 0.08 mm (0.039 ± 0.003 in)
-
136-2966 垫片
- 数量 ... 1
- 垫片厚度 ... 1.60 ± 0.10 mm (0.063 ± 0.004 in)
Show/hide table
图 2 | g01801815 |
D 区视图 |
注: 安装 7 条弹簧销 (15) 后,在弹簧销孔附近稍作定位标记。
(J) 从弹簧销孔边到定位标记的距离 ... 1.5 至 3.0 mm (0.06 至 0.12 in)
Caterpillar Information System:
MP-15, MP-20, MP-30 and MP-40 Multi Processors Hydraulic Cylinder
MP-15, MP-20, MP-30 and MP-40 Multi Processors Control Manifold - Crossover Relief Valve
312B Excavator Machine Systems Main Hydraulic Pump and Pump Drive Coupling - Install
MP-15, MP-20, MP-30 and MP-40 Multi Processors Swivel
MP-15, MP-20, MP-30 and MP-40 Multi Processors Gerotor Motor
G112, G115, G125 and G140 Mechanical Grapple Mounting Bracket
3064 and 3066 Engines for Caterpillar Built Machines Pinion Clearance - Adjust
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Final Drive - Remove
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Final Drive - Install
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Track Adjuster - Disassemble
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Undercarriage Frame - Remove
3512 and 3516 EUI Engines for 784B, 785B, 789B and 793B Off-Highway Trucks MID 036 - CID 0248 - FMI 09 Cat Data Link not communicating
3046 Engine for Caterpillar Built Machines Basic Engine
3408E and 3412E Engines for Caterpillar Built Machines Camshaft - Remove and Install
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Swing Gear and Bearing - Remove
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Swing Drive - Remove
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Swing Drive - Disassemble
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Swing Drive - Assemble
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Solenoid Valve (Hydraulic Lockout) - Remove and Install
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Swing Control Valve - Disassemble
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Swing Control Valve - Install
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Swing Control Valve - Remove
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Sprocket - Remove and Install
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Accumulator (Hydraulic Pilot) - Remove and Install