Swing Drive - Remove
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
(A)     | 132-8223     | 110 V Power Pack     | 1     |
1U-6221 | Torque Wrench     | 1     | |
132-8143 | Hex Link     | 1     | |
(B)     | 138-7574     | Link Bracket     | 2     |
Start By:
- Remove the swing motor. Refer to Disassembly and Assembly, "Swing Motor - Remove" in this manual.
Note: The removal procedure is identical for both swing drives. Only the right swing drive is removed in the following procedure.
- Thoroughly clean the area around the swing drive prior to removal.
- Drain the oil from the swing drive into a suitable container for storage or disposal. The capacity of the swing drive is 12 L (3.2 US gal).
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Put identification marks on the swing drive in order to mark the drive's location for installation purposes.
- Use Tooling (A) to remove bolts (1) and the washers that hold the swing drive to the upper frame.
Show/hide table
Illustration 1 | g00587094 |
- Remove the cork from the two threaded holes in the swing drive housing. Install a 24 mm forcing bolt in each threaded hole in the swing drive housing. Slowly tighten one forcing bolt for a few turns. Tighten the other forcing bolt for a few turns. Alternate between the forcing bolts in this manner in order to separate the swing drive from the main frame.
- Fasten Tooling (B) and an appropriate lifting device to swing drive (2). Remove swing drive (2) from the machine. The weight of the swing drive is approximately 380 kg (840 lb).
Show/hide table
Illustration 2 | g00587096 |
Caterpillar Information System:
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Swing Gear and Bearing - Remove
3408E and 3412E Engines for Caterpillar Built Machines Camshaft - Remove and Install
3046 Engine for Caterpillar Built Machines Basic Engine
365B and 365B Series II Excavators and 365B Series II Front Shovel Machine System Specifications Final Drive
MP-15, MP-20, MP-30 and MP-40 Multi Processors Hydraulic Cylinder
MP-15, MP-20, MP-30 and MP-40 Multi Processors Control Manifold - Crossover Relief Valve
312B Excavator Machine Systems Main Hydraulic Pump and Pump Drive Coupling - Install
MP-15, MP-20, MP-30 and MP-40 Multi Processors Swivel
MP-15, MP-20, MP-30 and MP-40 Multi Processors Gerotor Motor
G112, G115, G125 and G140 Mechanical Grapple Mounting Bracket
3064 and 3066 Engines for Caterpillar Built Machines Pinion Clearance - Adjust
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Final Drive - Remove
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Swing Drive - Disassemble
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Swing Drive - Assemble
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Solenoid Valve (Hydraulic Lockout) - Remove and Install
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Swing Control Valve - Disassemble
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Swing Control Valve - Install
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Swing Control Valve - Remove
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Sprocket - Remove and Install
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Accumulator (Hydraulic Pilot) - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump - Assemble
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Swing Drive - Install
G112, G115, G125 and G140 Mechanical Grapple Grapple
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Counterbalance Valve (Travel) - Remove and Install