Swing Gear and Bearing - Remove
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
(A)     | 138-7576     | Link Bracket     | 4     |
(B)     | 132-8223     | 110 volt Power Pack     | 1     |
1U-6221 | Torque Wrench     | 1     | |
1U-6222 | 46 mm Hex Link     | 1     |
Start By:
- Remove the undercarriage frame. Refer to Disassembly and Assembly, "Undercarriage Frame - Remove" in this manual.
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Remove all of the grease from the swing gear and bearing. Put the grease in a suitable container for storage or disposal.
- Put an alignment mark on the swing gear and bearing and the undercarriage frame for assembly purposes.
Show/hide table
Illustration 1 | g00616178 |
Typical example |
- Use Tooling (B) to remove bolts (2) that hold swing gear and bearing (1) to the undercarriage frame.
Show/hide table
Illustration 2 | g00616242 |
- Fasten Tooling (A) and a suitable lifting device to swing gear and bearing (1), as shown.
- Carefully remove the swing gear and bearing. The weight of the swing gear and bearing is approximately 1029 kg (2269 lb).
- Put tape over the sealing surfaces of the dust seals, the inner race and the outer race. The tape will prevent the cleaning solvent from entering the cross section of the dust seals. Thoroughly clean the swing gear and bearing.
Show/hide table
Illustration 3 | g00616248 |
- Remove dust seals (3) and (4) from the outer race and the inner race of the swing gear and bearing.
- Clean the sealing grooves of the inner race and the outer race with a fine grit sandpaper. Use a cleaning solvent to clean the seal grooves. Be sure that the seal grooves are thoroughly clean and dry prior to installing new dust seals.
Caterpillar Information System:
3408E and 3412E Engines for Caterpillar Built Machines Camshaft - Remove and Install
3046 Engine for Caterpillar Built Machines Basic Engine
365B and 365B Series II Excavators and 365B Series II Front Shovel Machine System Specifications Final Drive
MP-15, MP-20, MP-30 and MP-40 Multi Processors Hydraulic Cylinder
MP-15, MP-20, MP-30 and MP-40 Multi Processors Control Manifold - Crossover Relief Valve
312B Excavator Machine Systems Main Hydraulic Pump and Pump Drive Coupling - Install
MP-15, MP-20, MP-30 and MP-40 Multi Processors Swivel
MP-15, MP-20, MP-30 and MP-40 Multi Processors Gerotor Motor
G112, G115, G125 and G140 Mechanical Grapple Mounting Bracket
3064 and 3066 Engines for Caterpillar Built Machines Pinion Clearance - Adjust
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Final Drive - Remove
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Final Drive - Install
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Swing Drive - Remove
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Swing Drive - Disassemble
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Swing Drive - Assemble
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Solenoid Valve (Hydraulic Lockout) - Remove and Install
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Swing Control Valve - Disassemble
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Swing Control Valve - Install
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Swing Control Valve - Remove
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Sprocket - Remove and Install
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Accumulator (Hydraulic Pilot) - Remove and Install
3408E and 3412E Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump - Assemble
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Swing Drive - Install
G112, G115, G125 and G140 Mechanical Grapple Grapple