Temperature Sensor - Remove and Install - DPF Inlet, SCR Inlet
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | -     | LOCTITE 771 Anti-Seize Compound     | -     |
B     | -     | LOCTITE Nickel Anti-Seize     |     |
- Disconnect harness assembly (1). Cut any cable straps for this harness assembly.
Show/hide table
Illustration 1 | g03777641 |
Note: Mark the orientation of harness assembly (1) for assembly purposes.
- Remove DPF inlet temperature sensor (2). Cut any cable straps for the harness assembly.
Show/hide table
Illustration 2 | g03777658 |
- Disconnect harness assembly (3)
Show/hide table
Illustration 3 | g03779518 |
- Remove clips (4) and remove SCR inlet temperature sensor (5)
Installation Procedure
- Install the DPF inlet temperature sensor (2) and SCR inlet temperature sensor (5) in the reverse order of removal.
Note: Always replace the metal cable straps with a comparable cable strap. Do not use plastic cable straps.
Note: Route harness assembly (1) in the original location to protect harness assembly from heat.
- Apply Tooling (A) to the threads of DPF inlet temperature sensor (2). Tighten DPF inlet temperature sensor (2) to a torque of 45 ± 5 N·m (33 ± 4 lb ft).
- Apply Tooling (B) to the threads of SCR inlet temperature sensor (5). Tighten SCR inlet temperature sensor (5) to a torque of 45 ± 5 N·m (33 ± 4lb ft)
Caterpillar Information System:
C4.4 and C6.6 Engines Oil Contains Fuel
C4.4 and C7.1 Engines Oil Contains Coolant
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Engine Oil Coolers - Remove and Install
C15 Generator Set Generator Set - Test
C15 Generator Set Generator Bearing Temperature - Test/Record
465-0680 Top End Overhaul Foundational Kit for 3516 Generator Set Engines{1000} 465-0680 Top End Overhaul Foundational Kit for 3516 Generator Set Engines{1000}
C3.4B Engines Service Tool Features
C4.4 and C6.6 Engines Oil Consumption Is Excessive
C3.3 Industrial Engine Fuel System Secondary Filter/Water Separator - Drain
C3.3 Industrial Engine Maintenance Interval Schedule
3500E EPA Tier 4 Final and IMO-II/III Switchable Marine Engines Air Inlet and Exhaust System Operation - Aftertreatment
464-8152 Top End Overhaul Foundational Kit for 3516 Generator Set Engines{1000} 464-8152 Top End Overhaul Foundational Kit for 3516 Generator Set Engines{1000}
C3.4B Engines ECM Software - Install
2014/12/24 Accurate Diagnosis of Turbocharger Failure on Certain G3500 Engines {1052}
2014/12/19 Replacing the Hazardous Location Customer Connection Harness on Certain C9 and C15 Commercial Engines {1403, 1408}
336F XE Excavator Production Measurement Application
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Engine Oil Coolers - Disassemble
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Engine Oil Coolers - Assemble
Generators for C15/C18 Engines Voltage Regulators
C280 Marine and Petroleum Engines Turbocharger
C280 Marine Engines Camshaft
C280 Marine and Petroleum Engines Cylinder Block
C280 Marine Engines Cylinder Liner
C280 Marine and Petroleum Engines Fuel Injection Lines