Cylinder Block
Show/hide table
Illustration 1 | g06167612 |
Typical example Right side view |
Show/hide table
Specification for 441-1108 Cylinder Block Gp, 469-5047 Cylinder Block Gp, and 469-5048 Cylinder Block Gp | |||
---|---|---|---|
Item | Qty | Part | Specification Description |
1 | 24 | 6V-3539 Dowel | Before assembly, apply Chemtool Alpha 2000 Calcium Complex Grease.
Protrusion (B) of the dowel is |
2 | 27 | 6V-3538 Dowel | Protrusion (C) of the dowel is |
3 | 4 | 7N-2328 Dowel | Protrusion (D) of the dowel is |
Show/hide table
Illustration 2 | g06167613 |
Left side view |
Show/hide table
Item | Qty | Part | Specification Description |
---|---|---|---|
4 | 1 | 3P-0651 O-Ring Seal | Before assembly, lubricate the bore lightly with clean engine oil. |
5 | 2 | 3P-0656 O-Ring Seal | Before assembly, lubricate the bore lightly with clean engine oil. |
6 | 12 | 175-5060 Sleeve | Install the sleeve with the marked "TOP" toward up. |
Show/hide table
Illustration 3 | g06167615 |
Show/hide table
Item | Qty | Part | Specification Description |
---|---|---|---|
H | - | - | Bore in cylinder block for main bearing is |
J | - | - | The distance from the centerline of the crankshaft bearing bore to the top of the cylinder block is |
K | - | - | The distance from the centerline of the crankshaft bearing bore to the bottom of the cylinder block is |
7 | 7 | 124-1836 Bearing Cap As | The Bearing cap assembly must be installed with the part number toward the front of the block. The number of the main bearing cap must also match the cast number on the left side of each main bearing saddle. |
Width in the cylinder block for the bearing cap assembly is |
|||
Width (L) of bearing cap assembly is |
|||
Protrusion of 6V-3538 Dowel from the bearing cap assembly is |
Show/hide table
Illustration 4 | g06167620 |
Show/hide table
Item | Qty | Part | Specification Description |
---|---|---|---|
8 | 48 | 187-0450 Taperlock Stud | Use the following procedure to install the taperlock stud in the cylinder block: 1. Coat the lower half of each taperlock stud with 2. Install taperlock stud in the cylinder block. 3. Tighten the taperlock stud to 4. Coat the upper half of each taperlock stud with |
9 | 14 | 3S-7079 Bolt | Use the following procedure to tighten the main bearing assembly: 1. Again, tighten taperlock stud (12) in the cylinder block to 2. Assemble bearing cap assembly (7), washer (10), and hand tighten the nut (11). 3. Assemble all side bolt (9) on the tab slot side of the cap and hand tighten bolt (9). Before assembly, lubricate washer face and the threads of the bolts with clean engine oil. 4. Starting at front face of the block, tighten the side bolt (9) on the tab slot side of the cap to 5. Starting at front face of the block, simultaneously tension each pair of taperlock stud (12) with either tensioner 207-5034 Stud Tensioner Tool Gp or tensioner 191-5320 Stud Tensioner Tool Gp. Apply 6. Repeat Step 5. 7. Repeat sequentially Step 5 through Step 6 for cap (2) through cap (7). 8. Assemble all side bolt (9) on the side opposite to the tab slot side of the cap and hand tighten bolt (9). Before assembly, lubricate washer face and the threads of the bolts with clean engine oil. 9. Starting at front face of the block, tighten the side bolt (9) on the side opposite to the tab slot side of the cap to 10. Starting at front face of the block, tighten the side bolt (9) on tab slot side of the cap to 11. Starting at front face of the block, tighten the side bolt (9) on the side opposite to the tab slot side of the cap to |
10 | 14 | 1W-0122 Washer | |
11 | 14 | 1W-0123 Nut | |
12 | 14 | 1W-0121 Taperlock Stud |
Caterpillar Information System:
C280 Marine Engines Camshaft
C280 Marine and Petroleum Engines Turbocharger
Generators for C15/C18 Engines Voltage Regulators
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Engine Oil Coolers - Assemble
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Engine Oil Coolers - Disassemble
336F XE Excavator Production Measurement Application
2014/12/19 Replacing the Hazardous Location Customer Connection Harness on Certain C9 and C15 Commercial Engines {1403, 1408}
2014/12/24 Accurate Diagnosis of Turbocharger Failure on Certain G3500 Engines {1052}
C3.4B Engines ECM Software - Install
C13 Industrial Engine Temperature Sensor - Remove and Install - DPF Inlet, SCR Inlet
C4.4 and C6.6 Engines Oil Contains Fuel
C4.4 and C7.1 Engines Oil Contains Coolant
C280 Marine Engines Cylinder Liner
C280 Marine and Petroleum Engines Fuel Injection Lines
C280 Marine Engines Connecting Rod
C280 Marine Engines Crankshaft Seals
C280 Marine Engines Cylinder Block
C280 Marine Engines Housing (Front)
C280 Marine Engines Piston and Rings
C280 Marine Engines Flywheel
Procedure for Installing Continuous Telematics Power Retrofit (CTPR) for Electric Power{7606} Procedure for Installing Continuous Telematics Power Retrofit (CTPR) for Electric Power{7606}
C9.3 Marine Engines Fuel Pressure Sensor
C3.4B Engines ECM - Replace
C3.4B Engines Electrical Connectors - Inspect