Front Cover - Remove and Install
拆卸步骤
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 193-9199 | 套筒组件 | 1 |
| B | − | Loctite 271 | − |
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆下螺母 (2) 和螺栓 (1) ，然后拆下支架和皮带轮组件 (3) 。
Show/hide table
 | |
| 图 1 | g03529638 |
- 使用工具 (A) 拆下圆头螺钉 (4) 。
Show/hide table
 | |
| 图 2 | g03529657 |
- 将螺母 (7) 和隔套 (8) 从双头螺栓 (6) 上拆下。
- 将前盖 (5) 从前壳体上拆下。 将密封从前盖上拆下。
安装步骤
- 按与拆卸相反的顺序安装前盖 (5) 。
- 将圆头螺钉 (2) 上紧到 21 ± 3 N·m (186 ± 27 lb in) 的扭矩。
- 安装前，将工具 (B) 涂抹到螺柱 (4) 上。
Caterpillar Information System:
C280-16 Engine Crankcase Explosion Relief Valve - Remove and Install
C4.4 Engines for Caterpillar Built Machines Connecting Rod - For Use With Spheroidal Graphite Iron (SGI) Crankshaft
C4.4 Engines for Caterpillar Built Machines Main Bearing Journal - Spheroidal Graphite Iron (SGI) Crankshaft
C15 and C18 On-Highway Engines Vibration Damper and Pulley - Remove and Install
C4.4 Engines for Caterpillar Built Machines Connecting Rod Bearing Journal - Spheroidal Graphite Iron Crankshaft
C4.4 Engines for Caterpillar Built Machines Crankshaft - Spheroidal Graphite Iron (SGI) Crankshaft
C280-08 Marine Engine Plate Locations and Film Locations
C280-16 Engine Alternator - Remove and Install
2014/03/31 A New Rear Engine Crankshaft Seal Is Now Used on Certain Excavators Equipped With C13 Engines {1161}
C175 Oil Pressure Regulator Inspection and Rework{1304, 5117} C175 Oil Pressure Regulator Inspection and Rework{1304, 5117}
C15 and C18 On-Highway Engines Engine Control Module - Remove and Install
C15 and C18 On-Highway Engines Temperature Sensor (Cooled Exhaust Gas) - Remove and Install
A Procedure Is Available to Adapt the Glow Plug Harness to Certain Engines{1403, 1412} A Procedure Is Available to Adapt the Glow Plug Harness to Certain Engines{1403, 1412}
C15 and C18 On-Highway Engines Pressure Sensor (Cooled Exhaust Gas) - Remove and Install - Differential Pressure
C11 and C13 On-Highway Engines Compression Brake Lash - Adjust
C15 and C18 On-Highway Engines Pressure Sensor (Cooled Exhaust Gas) - Remove and Install - Outlet Pressure
C15 and C18 On-Highway Engines Boost Pressure Sensor - Remove and Install
C15 and C18 On-Highway Engines Inlet Air Temperature Sensor - Remove and Install
C15 and C18 On-Highway Engines Belt Tensioner - Remove and Install - Fan Belt Tensioner
Exhaust Balance Valve Causing Regeneration Issues On Certain Tier 4i C13 Engines{1061, 5479} Exhaust Balance Valve Causing Regeneration Issues On Certain Tier 4i C13 Engines{1061, 5479}
C15 and C18 On-Highway Engines Belt Tensioner - Remove and Install - Alternator Belt Tensioner
C280-16 Engine Prelubrication Oil Pump - Remove and Install
C280-16 Engine Air Starting Motor - Remove and Install
C15 and C18 On-Highway Engines Valve Mechanism Cover Base - Remove and Install