Engine Oil and Filter - Change
Show/hide table
 | |
| Illustration 1 | g02214433 |
- Remove the cap from the end of drain hose (1). Drain the oil into a suitable container.
Note: Refer to Operation and Maintenance Manual, "General Hazard Information" for more information on containing fluid spillage.
- Open the left side access panel in order to gain access to filter (2). Remove filter (2). Discard the used filter element.
Show/hide table
 | |
| Illustration 2 | g02560356 |
- Clean the filter housing base. All of the old filter seal must be removed from the filter housing base.
- Apply a thin coat of engine oil to the seal of the new filter element.
- Install the new filter by hand.
Instructions for the installation of the filter are printed on the side of each Caterpillar spin-on filter. For non-Caterpillar filters, refer to the installation instructions that are provided by the supplier of the filter.
- Close the access panel.
- Remove oil filler cap (4). Fill the crankcase with new oil. See Operation and Maintenance Manual, " Capacities (Refill)" for the correct refill capacity. Clean the oil filler cap and install the oil filler cap.
Show/hide table
 | |
| Illustration 3 | g02546440 |
- Check the engine oil level with oil level gauge (3). Maintain the oil level between the "FULL" mark and the "ADD" mark on the oil level gauge.
- Start the engine and run the engine for 2 minutes. Monitor the oil pressure gauge.
- Inspect the machine for oil leaks.
- Stop the engine.
- Wait for 10 minutes in order to allow the oil to drain back into the crankcase. Check the oil level.
Caterpillar Information System:
AP1000E Asphalt Paver Equipped with a Cat C6.6 Engine Engine Oil Sample - Obtain
2011/06/06 Radio Ready Series C SSL, MTL, and CTL Machines Are Now Available For Order {7338}
AP1000E Asphalt Paver Equipped with a Cat C6.6 Engine Engine Air Filter Primary Element - Clean/Replace
AP1000E Asphalt Paver Equipped with a Cat C6.6 Engine Engine Air Cleaner Inlet - Clean
326F Excavator Machine System Specifications Stick Cylinder
AP1000E and BG1000E Asphalt Pavers Propel System Piston Pump Neutral - Test and Adjust - Right Propel
AP1000E and BG1000E Asphalt Pavers Propel System Piston Pump Flow - Test
AP1000E and BG1000E Asphalt Pavers Propel System Hydraulic Oil Contamination - Test
AP1000E and BG1000E Asphalt Pavers Propel System Propel System Troubleshooting
C9.3 Tier 4 Final Engines Engine Oil Filter Base
C15 and C18 Engines for Caterpillar Built Machines Electric Starting Motor
2011/08/23 Introduction of Radiator Protection Screen on C4.4 and C4.4 (Mech) Engines {1353}
C175-16 Locomotive Engine Gear Group (Rear)
2470C, 2570C and 2670C Wheel Feller Bunchers Power Train Parking Brake - Remove and Install
AP1000E Asphalt Paver Equipped with a Cat C6.6 Engine Fuel System - Prime
AP1000E and BG1000E Asphalt Pavers Propel System Piston Pump Neutral - Test and Adjust - Left Propel
AP1000E Asphalt Paver Equipped with a Cat C6.6 Engine Fuel System Secondary Filter - Replace
735B, 740B and 740B EJECTOR Articulated Trucks Engine Supplement Engine Front Mount - Remove and Install
Topcon® System Five Safety Messages
AP1000E and BG1000E Asphalt Pavers Propel System Pump Synchronization - Test and Adjust
AP1000E and BG1000E Asphalt Pavers Propel System Pressure Limiter Valve - Test and Adjust - Right Pump
AP1000E and BG1000E Asphalt Pavers Propel System Pressure Limiter Valve - Test and Adjust - Left Pump
AP1000E and BG1000E Asphalt Pavers Propel System Relief Valve (Charge) - Test and Adjust - Right Pump
AP1000E and BG1000E Asphalt Pavers Propel System Relief Valve (Charge) - Test and Adjust - Left Pump