C15 and C18 Engines for Caterpillar Built Machines Caterpillar


Electric Starting Motor

Usage:

826K 2L3


图 1g02560026

表 1
技术规格,用于 207-1556 电动起动马达总成 
项目  数量  零件  技术规格说明 
6V-8188 螺母  拧紧至扭矩为 30.5 ± 3.5 N·m (269.9 ± 31.0 lb in)。 
250-8279 电磁阀套件  20V 和 25 °C (77 °F) 下的电流消耗:
1. 对于吸合绕组为 57 安培
2. 对于保持绕组为 16 安培
3. 最大额定电流为 850 安培 
小齿轮和壳体之间的间隙为 9.1 mm (0.36 inch)。 
6V-8378 螺母  拧紧至扭矩为 2.6 ± 0.8 N·m (23.0 ± 7.1 lb in)。 
6V-8188 螺母  蓄电池端子螺母(3)最多可使用三个电缆或导线端子。 两个端子最高不低于 0 AWG。
拧紧至扭矩为 30.5 ± 3.5 N·m (269.9 ± 31.0 lb in)。 
6V-8378 螺母  开关端子必须用热收缩管绝缘。 不要使用模压端子。
拧紧至扭矩为 2.6 ± 0.8 N·m (23.0 ± 7.1 lb in)。 
6V-8188 螺母  拧紧至扭矩为 30.5 ± 3.5 N·m (269.9 ± 31.0 lb in)。 
拧紧至扭矩为 8 ± 3 N·m (71 ± 27 lb in)。 
当从小齿轮端观看电起动马达时,马达顺时针旋转。
25 °C (77 °F) 下的无负载状态
1. 转速为 7643 ± 1683 rpm
2. 电流消耗为 76.5 ± 14.5 安培
3. 电压为 23 V 

Caterpillar Information System:

2011/08/23 Introduction of Radiator Protection Screen on C4.4 and C4.4 (Mech) Engines {1353}
320E and 323E Excavators Machine System Specifications Auxiliary Pump Drive and Mounting
326F Excavator Machine System Specifications Boom Cylinder
C175-16 Locomotive Engine Cylinder Liner
C13, C15, and C18 Generator Set Engines Turbocharger
Spill Guard Installation Procedure for Certain Buckets on R2900G Load Haul Dump Machines{7186} Spill Guard Installation Procedure for Certain Buckets on R2900G Load Haul Dump Machines{7186}
R1600G Load Haul Dump 3176C Engine Supplement Transmission Oil Cooler - Remove
SC-57 Felling Head Felling Head Disc Saw Performance - Test and Adjust
C9.3 Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove and Install
C9.3 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C9.3 Engines for Caterpillar Built Machines Flywheel - Remove and Install
2470C, 2570C and 2670C Wheel Feller Bunchers Power Train Brake Accumulator (Service) - Remove and Install
C9.3 Tier 4 Final Engines Engine Oil Filter Base
AP1000E and BG1000E Asphalt Pavers Propel System Propel System Troubleshooting
AP1000E and BG1000E Asphalt Pavers Propel System Hydraulic Oil Contamination - Test
AP1000E and BG1000E Asphalt Pavers Propel System Piston Pump Flow - Test
AP1000E and BG1000E Asphalt Pavers Propel System Piston Pump Neutral - Test and Adjust - Right Propel
326F Excavator Machine System Specifications Stick Cylinder
AP1000E Asphalt Paver Equipped with a Cat C6.6 Engine Engine Air Cleaner Inlet - Clean
AP1000E Asphalt Paver Equipped with a Cat C6.6 Engine Engine Air Filter Primary Element - Clean/Replace
2011/06/06 Radio Ready Series C SSL, MTL, and CTL Machines Are Now Available For Order {7338}
AP1000E Asphalt Paver Equipped with a Cat C6.6 Engine Engine Oil Sample - Obtain
AP1000E Asphalt Paver Equipped with a Cat C6.6 Engine Engine Oil and Filter - Change
C175-16 Locomotive Engine Gear Group (Rear)
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.