Brake Accumulator (Service) - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | QTY |
A | 311-1362 | Vacuum Cap | 1 |
- Connect steering frame lock.
- Release system pressure.
- Install Tooling (A) onto the hydraulic tank. Attach an air supply hose onto Tooling (A). Apply
138 kPa (20 psi) . This procedure will pull a vacuum on the hydraulic system. - Tilt cab.
Show/hide table
Illustration 1 g02560279 Show/hide tablePersonal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
- Release any pressure in the accumulator by turning valve (1).
Show/hide table
Illustration 2 g02560281 - Remove hose assembly (3) and bolts (2).
Show/hide table
Illustration 3 g02560297 - Remove bolts (4) and brake accumulator (5).
- Install brake accumulator (5) in the reverse order of removal.
Caterpillar Information System:
2011/08/26 A New Wiring Harness Is Used On Certain Commercial Engines {1408, 1900}
2470C, 2570C and 2670C Wheel Feller Bunchers Power Train Drive Shaft (Rear) - Remove and Install
262C2 Skid Steer Loader, 277C2 and 287C2 Multi Terrain Loaders and 279C2 and 289C2 Compact Track Loaders Rated Load
2470C, 2570C and 2670C Wheel Feller Bunchers Power Train Drive Shaft (Center) - Remove and Install
AP1000E Asphalt Paver Equipped with a Cat C6.6 Engine Declaration of Conformity
2470C, 2570C and 2670C Wheel Feller Bunchers Power Train Drive Shaft (Front) - Remove and Install
824K Wheel Dozer, 825K Soil Compactor and 826K Landfill Compactor Machine Systems Pressure Sensor (Service Brake Oil)
2011/06/08 Improved Magnetic Switch Is Now Used For Electric Motors On Certain Articulated Trucks {4324, 5927, 7499}
XQ125 Generator Set Fuel Tank Water and Sediment - Drain
SC-57 Felling Head Felling Head Preparation for Troubleshooting
Additional Procedure when Replacing the Engine, ECM, or CEM Tier 4 Engines{1000, 108D, 108F, 1901} Additional Procedure when Replacing the Engine, ECM, or CEM Tier 4 Engines{1000, 108D, 108F, 1901}
2570C and 2670C Wheel Feller Bunchers Engine Supplement Turbocharger - Install - First Stage Turbocharger
C9.3 Engines for Caterpillar Built Machines Flywheel - Remove and Install
C9.3 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C9.3 Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove and Install
SC-57 Felling Head Felling Head Disc Saw Performance - Test and Adjust
R1600G Load Haul Dump 3176C Engine Supplement Transmission Oil Cooler - Remove
Spill Guard Installation Procedure for Certain Buckets on R2900G Load Haul Dump Machines{7186} Spill Guard Installation Procedure for Certain Buckets on R2900G Load Haul Dump Machines{7186}
C13, C15, and C18 Generator Set Engines Turbocharger
C175-16 Locomotive Engine Cylinder Liner
326F Excavator Machine System Specifications Boom Cylinder
320E and 323E Excavators Machine System Specifications Auxiliary Pump Drive and Mounting
2011/08/23 Introduction of Radiator Protection Screen on C4.4 and C4.4 (Mech) Engines {1353}
C15 and C18 Engines for Caterpillar Built Machines Electric Starting Motor