Turbocharger
Show/hide table
| |
| Illustration 1 | g01456476 |
|
Right side view of engine | |
Show/hide table
| Specification for 211-7814 Turbocharger Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 1 | 4P-3629 Compressor Clamp Assembly | Use the following procedure to tighten the clamps for the turbocharger. Orient the turbocharger turbine housing and the bearing housing in order to avoid binding:
1. Loosen the clamp assemblies in order to rotate the housings. 2. Position the housings with oil lines so that oil lines are aligned without binding. 3. Tighten to 4. Lightly tap around the clamp assemblies with a soft faced hammer. 5. Again, tighten to |
| 2 | 1 | 137-1602 Clamp As | |
| 3 | 8 | 2N-2765 High Temperature Bolts | Before assembly, apply 4C-5599 Anti-Seize Compound to the threads.
Torque to |
Caterpillar Information System:
Spill Guard Installation Procedure for Certain Buckets on R2900G Load Haul Dump Machines{7186} Spill Guard Installation Procedure for Certain Buckets on R2900G Load Haul Dump Machines{7186}
R1600G Load Haul Dump 3176C Engine Supplement Transmission Oil Cooler - Remove
SC-57 Felling Head Felling Head Disc Saw Performance - Test and Adjust
C9.3 Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove and Install
C9.3 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C9.3 Engines for Caterpillar Built Machines Flywheel - Remove and Install
2470C, 2570C and 2670C Wheel Feller Bunchers Power Train Brake Accumulator (Service) - Remove and Install
2011/08/26 A New Wiring Harness Is Used On Certain Commercial Engines {1408, 1900}
2470C, 2570C and 2670C Wheel Feller Bunchers Power Train Drive Shaft (Rear) - Remove and Install
262C2 Skid Steer Loader, 277C2 and 287C2 Multi Terrain Loaders and 279C2 and 289C2 Compact Track Loaders Rated Load
2470C, 2570C and 2670C Wheel Feller Bunchers Power Train Drive Shaft (Center) - Remove and Install
AP1000E Asphalt Paver Equipped with a Cat C6.6 Engine Declaration of Conformity
C175-16 Locomotive Engine Cylinder Liner
326F Excavator Machine System Specifications Boom Cylinder
320E and 323E Excavators Machine System Specifications Auxiliary Pump Drive and Mounting
2011/08/23 Introduction of Radiator Protection Screen on C4.4 and C4.4 (Mech) Engines {1353}
C15 and C18 Engines for Caterpillar Built Machines Electric Starting Motor
C9.3 Tier 4 Final Engines Engine Oil Filter Base
AP1000E and BG1000E Asphalt Pavers Propel System Propel System Troubleshooting
AP1000E and BG1000E Asphalt Pavers Propel System Hydraulic Oil Contamination - Test
AP1000E and BG1000E Asphalt Pavers Propel System Piston Pump Flow - Test
AP1000E and BG1000E Asphalt Pavers Propel System Piston Pump Neutral - Test and Adjust - Right Propel
326F Excavator Machine System Specifications Stick Cylinder
AP1000E Asphalt Paver Equipped with a Cat C6.6 Engine Engine Air Cleaner Inlet - Clean