Crankshaft - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7576     | 连杆支架     | 2     |
开始:
- 拆卸驱动器壳体。 请参阅拆解和组装, "驱动轴壳体(后)- 拆卸和安装"。
- 拆下飞轮壳体。 请参阅拆解和组装, "飞轮壳体 - 拆卸"。
- 拆下排气歧管。 请参阅拆解和组装, "排气歧管 - 拆卸"。
- 拆下摇臂轴组件和推杆。 请参阅拆解和组装, "摇臂轴和推杆 - 拆卸"。
- 将发动机置于水平位置。
- 在配重 (1) 上贴上标记。 拆卸配重 (1) 。
注: 如果从发动机上拆卸活塞和连杆组件,则没必要从曲轴上拆卸配重。
Show/hide table
图 1 | g00914774 |
- 拆卸连杆轴承盖 (2) 。 将连杆推离曲轴。 分别从连杆和连杆盖 (2) 上拆下连杆轴承。
Show/hide table
图 2 | g00914776 |
- 拆卸中心主轴承和止推板 (3) 。
Show/hide table
图 3 | g00914800 |
- 将工具 (A) 和适当的起吊设备连接到曲轴 (5) 上。
Show/hide table
图 4 | g01058477 |
- 拆卸剩余的主轴承盖 (4) 。 从主轴承盖 (4) 上拆卸曲轴主轴承的下半部分。
- 拆下曲轴 (5) 。
带配重的 3516 曲轴的重量约为 800 kg (1764 lb)。 不带配重的 3516 曲轴的重量约为 520 kg (1146 lb)。 带配重的 3520 曲轴的重量约为 920 kg (2028 lb)。 不带配重的 3520 曲轴的重量约为 580 kg (1280 lb)。
- 从缸体上拆下曲轴主轴承的上半部分。
- 如有必要,从曲轴的每一端拆卸螺栓 (6) 和曲轴齿轮 (7) 。
Show/hide table
图 5 | g00914805 |
Caterpillar Information System:
2003/06/01 Removal of Elbow Improves the Reliability of the Cooling System in an Industrial Application {1380}
XQP60 and XQP100 Rental Generator Sets Fuel System - Prime
3500B Series II Marine Engines Direct Fuel Control Mode
3500B Series II Marine Engines Engine Speed/Timing Sensor - Calibrate
C3.3 Industrial Engine Cold Weather Starting
2003/06/01 New Waterproof Covers for Magnetos are Used {1552}
C7 On-highway Engine Turbocharger
C4.4 Generator Sets Engine Stopping
XQP60 and XQP100 Rental Generator Sets Model View Illustrations
C15 On-highway Engine Turbocharger - Install - High Pressure
C15 On-highway Engine Turbocharger - Remove - High Pressure
C7 On-highway Engine Belt Tensioner - If Equipped
G3520C and G3520E Generator Set Engines Crankshaft - Install
G3500 Engines MID 018 - CID 0550 - FMI 02 Noisy or Loss of Oxygen Signal
C3.3 Industrial Engine Engine Warm-up
G3304 and G3306 Engines Cylinder Liner - Install
G3500 Engines MID 018 - CID 0523 - FMI 11 No A/F Ratio Engine Speed Sensor **Shutdown**
Bench Test Procedure for Hydraulic Piston Pumps{5070} Bench Test Procedure for Hydraulic Piston Pumps{5070}
C11, C13 and C15 On-highway Engines 0105-03 Intake Manifold Air Temperature voltage high (38)
C11, C13 and C15 On-highway Engines 0105-04 Intake Manifold Air Temperature voltage low (38)
G3304 and G3306 Engines Camshaft Bearings - Remove
G3304 and G3306 Engines Camshaft Bearings - Install
3406C Marine Auxiliary Generator Set Plate Locations and Film Locations
G3304 and G3306 Engines Crankshaft - Remove