Plate (Trench Cleaner) - Remove and Install
Removal Procedure
Show/hide table
| Required Tools | |||
| Tool | Pt. No. | Description | Qty |
| A | 1U-9200 | Lever Puller Hoist | 2 |
| B | 180-3033 | Jack Stand Gp (1) | 1 |
| C | 138-7575 | Link Bracket | 2 |
Show/hide table
| ( 1 ) | Tooling (B) is from the Start By tooling list in the removal procedure. This tooling is included for reference. |
Start By:
- Remove the trench cleaner cylinder. Refer to the Disassembly and Assembly Manual, "Hydraulic Cylinder (Trench Cleaner) - Remove and Install".
- Remove bolts (2) and move cable assembly (1) aside.
Show/hide table
 | |
| Illustration 1 | g01014402 |
- Attach Tooling (A) and (C) to plate assembly (3). The plate assembly weighs approximately 60 kg (130 lb).
Show/hide table
 | |
| Illustration 2 | g01014403 |
- Use Tooling (A) to raise the plate assembly.
- Remove the Tooling (B) from below plate assembly (3) .
Show/hide table
 | |
| Illustration 3 | g01017831 |
- Use Tooling (A) to lower the plate assembly to the ground.
Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Pt. No. | Description | Qty |
| A | 1U-9200 | Lever Puller Hoist | 2 |
| B | 180-3033 | Jack Stand Gp (1) | 1 |
| C | 138-7575 | Link Bracket | 2 |
Show/hide table
| ( 1 ) | Tooling (B) is from the Start By tooling list in the removal procedure. This tooling is included for reference. |
- Use Tooling (A) and (C) to raise plate assembly (3).
Show/hide table
| | |
| Illustration 4 | g01014403 |
- Install the Tooling (B) in order to support plate assembly (3) .
Show/hide table
 | |
| Illustration 5 | g01013819 |
- Remove Tooling (A) and (C) .
- Install cable assembly (1) and bolts (2) .
Show/hide table
| | |
| Illustration 6 | g01014402 |
End By: Install the trench cleaner cylinder. Refer to the Disassembly and Assembly Manual, "Hydraulic Cylinder (Trench Cleaner) - Remove and Install".
Caterpillar Information System:
SW45 and SW60 Wheel Saws Cable (Trench Cleaner) - Remove and Install
SW45 and SW60 Wheel Saws Guide (Trench Cleaner) - Remove and Install
321C LCR Excavator Machine Systems Drift Reduction Valve (Stick) - Install
321C LCR Excavator Machine Systems Drift Reduction Valve (Stick) - Remove
321C LCR Excavator Machine Systems Drift Reduction Valve (Boom) - Remove
321C LCR Excavator Machine Systems Drift Reduction Valve (Boom) - Install
M322C Excavator Hydraulic System Hydraulic System - Setup - Combined Function Valve
C27 and C32 Generator Set Engines Camshaft Bearings - Install
C27 and C32 Generator Set Engines Camshaft Bearings - Remove
3046 Engine for Caterpillar Built Machines Belt Tension Chart
2003/08/01 New Hose Improves the Drainage of Oil from the Turbocharger During a Continuous Prelube Cycle {1052}
2003/08/18 New Sleeve Bearings in the Oscillating Axle Trunnion Support Improve Service Life {3268, 7551}
2003/07/28 Disregard theService Magazine , "Correction to Systems Operation Testing and Adjusting , "Engine Speed Control"" {1931}
325C and 325C L Excavator Hydraulic System Oil Sample - Obtain
322C Excavator Safety Messages - Arrangement I
321C LCR Excavator Machine Systems Shuttle Valve - Remove - Auxiliary Control
321C LCR Excavator Machine Systems Shuttle Valve - Install - Auxiliary Control
321C LCR Excavator Machine Systems Swing Motor - Remove
321C LCR Excavator Machine Systems Swing Motor - Install
2003/09/22 Improved Air Cleaner Bracket for the 302.5 and 303.5 Mini Hydraulic Excavator {1051}
SW45 and SW60 Wheel Saws Wheel Saw Drum - Remove and Install
G3500B Engines Engine Protective Devices - Check
SW45 and SW60 Wheel Saws Bearing - Remove and Install
SW45 and SW60 Wheel Saws Control Manifold - Assemble