Removal Procedure
Required Tools     | |||
Tool     | Pt. No.     | Description     | Qty     |
A     | 4C-6486     | Stand     | 4     |
8S-7641 | Tube     | 2     | |
8S-7621 | Tube     | 2     | |
8S-7625 | Collar     | 1     | |
8S-8048 | Saddle     | 4     | |
8S-7615 | Pin     | 4     | |
189-0411 | Shackle As     | 1     | |
- | Pipe (51 mm (2 inch) OD)     | 1     | |
B     | 180-3033     | Jack Stand Gp     | 1     |
ZZ     | 6V-9508     | Face Seal Plug     | 2     |
6V-9829 | Cap As     | 2     |
Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN PHOTOGRAPHS IN THE REMOVAL OR IN THE INSTALLATION. THIS TOOLING IS SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Use Tooling (A) to support the work tool.
Illustration 1 | g01013336 |
Illustration 2 | g01013350 |
- Use Tooling (B) to support the trench cleaner.
Illustration 3 | g01013819 |
- Remove bolts (1) .
Illustration 4 | g01014328 |
- Disconnect hose assemblies (2) and (3) .
- Remove plates (4) and (5) .
- Remove U-bolts (7) .
Illustration 5 | g01014332 |
- Remove cable assembly (6) .
Installation Procedure
Required Tools     | |||
Tool     | Pt. No.     | Description     | Qty     |
A     | 4C-6486     | Stand     | 4     |
8S-7641 | Tube     | 2     | |
8S-7621 | Tube     | 2     | |
8S-7625 | Collar     | 1     | |
8S-8048 | Saddle     | 4     | |
8S-7615 | Pin     | 4     | |
189-0411 | Shackle As     | 1     | |
- | Pipe (51 mm (2 inch) OD)     | 1     | |
B     | 180-3033     | Jack Stand Gp     | 1     |
Note: Inspect all O-ring seals for wear or for damage. Replace the components, if necessary.
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
NOTICE |
---|
Keep all parts clean from contaminants. Contamination of the hydraulic system with foreign material will reduce the service life of the hydraulic system components. To prevent contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected. Cover any disassembled components and clean them properly before assembly. Clean the hydraulic system properly after any major component exchange or especially after a component failure, to remove any contamination. |
- Install cable assembly (6) .
Illustration 6 | g01014332 |
- Install U-bolts (7) .
- Install plates (4) and (5) .
Illustration 7 | g01014328 |
- Install the O-ring seals and hose assemblies (2) and (3) .
- Install bolts (1) .
- Remove the work tool from Tooling (A) and (B) .