Oil Fill Capacity for the Circle Drive Housing has been Updated on Certain 14M Series 3 Motor Graders {0374, 5207}
- Motor Grader
- 14M Series 3 (S/N: E9S251-264; N9S236-261)
Reference: Operation and Maintenance Manual , SEBU9257 , "Circle Drive Oil - Change"
Description Of Change: Oil fill capacity for the circle drive housing has been updated on the machines listed above. The updated oil fill specification will improve the circle drive performance and aids the ideal hydraulic system functionality.
Adaptable To: The following changes are adaptable to the products within the listed serial numbers, and are effective with all products after the listed serial numbers.
Show/hide table
 |
|
Do not operate or work on this product unless you have read and understood the instruction and warnings in the relevant Operation and Maintenance Manuals and relevant service literature. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility. |
Show/hide table
| |
| Illustration 1 | g06307010 |
|
View of the circle drive housing showing correct oil level (A) The correct oil level (1) Worm gear inside the circle drive housing | |
The correct oil fill volume for the circle drive housing has now been updated to
Note: Fill the oil to the top of the worm gear (1). Ensure that the oil level is slightly above the worm gear as shown in Illustration 1.
Caterpillar Information System:
A New Thermowell Is Available for Certain C175 Off-Highway Truck/Tractor Engines {7498} A New Thermowell Is Available for Certain C175 Off-Highway Truck/Tractor Engines {7498}
MP318, MP324, MP332, MP345 and and MP365 Multi-Processors and Jaws Control Manifold
New C175 High Altitude Low Maintenance Ratio Engine for 797 Off-Highway Trucks {1000} New C175 High Altitude Low Maintenance Ratio Engine for 797 Off-Highway Trucks {1000}
Troubleshooting Procedures for Supercom Data Acquisition Systems are Now Available for Certain Off-Highway Trucks {7600, 7601, 7606, 7620} Troubleshooting Procedures for Supercom Data Acquisition Systems are Now Available for Certain Off-Highway Trucks {7600, 7601, 7606, 7620}
The Buffer Seal Assembly in the Steering Cylinder Group May Wear Prematurely on Certain 773G, 775G, and 777G Off-Highway Trucks {4303, 7555} The Buffer Seal Assembly in the Steering Cylinder Group May Wear Prematurely on Certain 773G, 775G, and 777G Off-Highway Trucks {4303, 7555}
Shims Added to Coupler to Decrease Side to Side Motion Are Now Used on Certain Compact Track Loaders, Multi Terrain Loaders, and Skid Steer Loaders {6129, 7000} Shims Added to Coupler to Decrease Side to Side Motion Are Now Used on Certain Compact Track Loaders, Multi Terrain Loaders, and Skid Steer Loaders {6129, 7000}
C175 Tier 4 Final Engines for Caterpillar Built Machines Air Inlet Manifold - Remove and Install
3516E Engines for Caterpillar Built Machines Fuel Priming Pump - Remove and Install - With Fuel/Water Separator
2570C and 2670C Wheel Feller Bunchers Cab Tilting
C7 Engines for Caterpillar Built Machines Unit Injector Hydraulic Pump
An Improved Wheel Speed Sensor is Now Available on Certain RM500B Rotary Mixers {4351, 5058} An Improved Wheel Speed Sensor is Now Available on Certain RM500B Rotary Mixers {4351, 5058}
Cleaning Procedure for the Polycarbonate Windshields, Windows, and Skylights on Certain Forest Machines, Track Feller Bunchers, Wheel Feller Bunchers, and Wheel Skidders {7310, 7340} Cleaning Procedure for the Polycarbonate Windshields, Windows, and Skylights on Certain Forest Machines, Track Feller Bunchers, Wheel Feller Bunchers, and Wheel Skidders {7310, 7340}
Product Link ® Elite PLE742 Systems Service Tools
563D and 573D Wheel Feller Buncher Windows - Clean
3516E Engines for Caterpillar Built Machines Vibration Damper - Remove and Install
3512C Engines for 785C Off-Highway Trucks with Dynamic Gas Blending Intake Manifold Air Temperature Is High
CB64B, CB66B and CB68B Asphalt Compactors Machine Electronic Control System Machine Steer not Responding Properly
AP655F and AP655F L Asphalt Paver Declaration of Conformity
Improved Engine Software and Diesel Exhaust Fluid Injector Assembly Is Now Used on Certain Material Handlers, Mobile Hydraulic Power Units, and Wheeled Excavators {108I, 7610, 7620} Improved Engine Software and Diesel Exhaust Fluid Injector Assembly Is Now Used on Certain Material Handlers, Mobile Hydraulic Power Units, and Wheeled Excavators {108I, 7610, 7620}
New Preservation Process for Crankshafts is Now Used for 3500, G3500, and C175-16 Series Engines {1202} New Preservation Process for Crankshafts is Now Used for 3500, G3500, and C175-16 Series Engines {1202}
New Preservation Process for Crankshafts is Now Used for 3500, G3500, and C175-16 Series Engines {1202} New Preservation Process for Crankshafts is Now Used for 3500, G3500, and C175-16 Series Engines {1202}
The Pressure Setting on the Hoist Raise Valve Group May Be Low on Certain Off-Highway Trucks {5051, 5069, 5117} The Pressure Setting on the Hoist Raise Valve Group May Be Low on Certain Off-Highway Trucks {5051, 5069, 5117}
The Housing Assembly for the Front Suspension Group May Crack on Certain 773G and 775G Off-Highway Trucks {7200, 7201} The Housing Assembly for the Front Suspension Group May Crack on Certain 773G and 775G Off-Highway Trucks {7200, 7201}
An Improved Rear Wheel Bearing for Certain Large Off-Highway Trucks is Available {4008, 7551} An Improved Rear Wheel Bearing for Certain Large Off-Highway Trucks is Available {4008, 7551}