Show/hide table
|
Personal injury can result from rotating and moving parts. Stay clear of all rotating and moving parts. Never attempt adjustments while the machine is moving or the engine is running unless otherwise specified. The machine must be parked on a level surface and the engine stopped. Attach a "Do Not Operate" or similar warning tag to the start switch and controls before servicing, repairing, or making adjustments to the machine. |
|
Show/hide table
|
Personal injury or death can result from sudden machine movement. Sudden movement of the machine can cause injury to persons on or near the machine. To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine. |
|
Calibration of Left Paddle Sensor
- Drive the machine to a smooth, horizontal surface.
Show/hide table
|
|
|
Illustration 1 | g01473996 |
- Move propel lever (3) to the NEUTRAL position.
- Rotate speed dial (2) to the MINIMUM position.
- Move parking brake switch (1) to the ON position.
Show/hide table
|
|
|
Illustration 2 | g01473997 |
- Move screed lift switch (4) to the RAISE position. Completely lift the screed.
Show/hide table
|
|
|
Illustration 3 | g01510335 |
- Engage screed lock mechanism (5) on both sides of the machine.
- Move screed lift switch (4) to the FLOAT position.
Note: The screed lift switch on the inactive instrument panel must also be in the FLOAT position in order to lower the screed.
Show/hide table
|
|
|
Illustration 4 | g01510336 |
- Move right screed extend switch (7) to the EXTEND position. Release the switch when the right screed extender is fully extended.
- Move left screed extend switch (6) to the EXTEND position. Release the switch when the left screed extender is fully extended.
Show/hide table
|
|
|
Illustration 5 | g01510338 |
- Move throttle control switch (8) to the LOW IDLE position. Hold the switch in this position for less than 1 second.
- After the engine reaches low idle, move engine start switch (9) to the OFF position.
- Move screed lift switch (4) to the HOLD position.
- Move engine start switch (9) to the ON position. Do not start the engine.
Show/hide table
|
|
|
Illustration 6 | g01514027 |
- Press home key (10) .
Show/hide table
|
|
|
Illustration 7 | g01514028 |
- Press down key (11) until "Service" is highlighted on the display screen.
- Press OK key (12) .
Show/hide table
|
|
|
Illustration 8 | g01514029 |
- Press down key (11) until "Calibrations" is highlighted on the display screen.
- Press OK key (12) .
Show/hide table
|
|
|
Illustration 9 | g01514031 |
- Press down key (11) until "Left Paddle Sensor" is highlighted on the display screen.
- Press OK key (12) .
- Press OK key (12) in order to begin the calibration.
Show/hide table
|
|
|
Illustration 10 | g01514035 |
- Press OK key (12) .
Show/hide table
|
|
|
Illustration 11 | g01514037 |
Show/hide table
|
|
|
Illustration 12 | g01514041 |
- Hold left paddle (13) in the full OFF position at approximately 45 degrees. Press OK key (12) .
Show/hide table
|
|
|
Illustration 13 | g01514042 |
Show/hide table
|
|
|
Illustration 14 | g01514044 |
- Place left paddle (13) in the full ON position. This position should be straight down. Press OK key (12) .
Show/hide table
|
|
|
Illustration 15 | g01514046 |
- The display should now read "CALIBRATION COMPLETE". Push back key (14) in order to return to the calibration screen.
- Push home key (10) in order to exit the calibration screen.
- Move engine start switch (9) to the OFF position.
Calibration of Right Paddle Sensor
- Drive the machine to a smooth, horizontal surface.
Show/hide table
|
|
|
Illustration 16 | g01473996 |
- Move propel lever (3) to the NEUTRAL position.
- Rotate speed dial (2) to the MINIMUM position.
- Move parking brake switch (1) to the ON position.
Show/hide table
|
|
|
Illustration 17 | g01473997 |
- Move screed lift switch (4) to the RAISE position. Completely lift the screed.
Show/hide table
|
|
|
Illustration 18 | g01510335 |
- Engage screed lock mechanism (5) on both sides of the machine.
- Move screed lift switch (4) to the FLOAT position.
Note: The screed lift switch on the inactive instrument panel must also be in the FLOAT position in order to lower the screed.
Show/hide table
|
|
|
Illustration 19 | g01510336 |
- Move right screed extend switch (7) to the EXTEND position. Release the switch when the right screed extender is fully extended.
- Move left screed extend switch (6) to the EXTEND position. Release the switch when the left screed extender is fully extended.
Show/hide table
|
|
|
Illustration 20 | g01510338 |
- Move throttle control switch (8) to the LOW IDLE position. Hold the switch in this position for less than 1 second.
- After the engine reaches low idle, move engine start switch (9) to the OFF position.
- Move screed lift switch (4) to the HOLD position.
- Move engine start switch (9) to the ON position. Do not start the engine.
Show/hide table
|
|
|
Illustration 21 | g01514027 |
- Press home key (10) .
Show/hide table
|
|
|
Illustration 22 | g01514027 |
- Press down key (11) until "Service" is highlighted on the display screen.
- Press OK key (12) .
Show/hide table
|
|
|
Illustration 23 | g01514028 |
- Press down key (11) until "Calibrations" is highlighted on the display screen.
- Press OK key (12) .
Show/hide table
|
|
|
Illustration 24 | g01514050 |
- Press down key (11) until "Right Paddle Sensor" is highlighted on the display screen.
- Press OK key (12) .
- Press OK key (12) in order to begin the calibration.
Show/hide table
|
|
|
Illustration 25 | g01514053 |
- Press OK key (12) .
Show/hide table
|
|
|
Illustration 26 | g01514055 |
Show/hide table
|
|
|
Illustration 27 | g01514056 |
- Hold right paddle (13) in the full OFF position at approximately 45 degrees. Press OK key (12) .
Show/hide table
|
|
|
Illustration 28 | g01514058 |
Show/hide table
|
|
|
Illustration 29 | g01514059 |
- Place right paddle (13) in the full ON position. This should be straight down. Press OK key (12) .
Show/hide table
|
|
|
Illustration 30 | g01514064 |
- The display should now read "CALIBRATION COMPLETE". Push back key (14) in order to return to the calibration screen.
- Push home key (10) in order to exit the calibration screen.
- Move engine start switch (9) to the OFF position.