Personal injury can result from rotating and moving parts. Stay clear of all rotating and moving parts. Never attempt adjustments while the machine is moving or the engine is running unless otherwise specified. The machine must be parked on a level surface and the engine stopped. Attach a "Do Not Operate" or similar warning tag to the start switch and controls before servicing, repairing, or making adjustments to the machine. |
Personal injury or death can result from sudden machine movement. Sudden movement of the machine can cause injury to persons on or near the machine. To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine. |
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 1U-6602     | Photo-Tachometer     | 1     |
- Drive the machine to a smooth, horizontal surface.
- Move propel lever (3) to the NEUTRAL position.
Illustration 1 | g01473996 |
- Rotate speed dial (2) to the MINIMUM position.
- Move parking brake switch (1) to the ON position.
- Move screed lift switch (4) to the RAISE position. Completely lift the screed.
Illustration 2 | g01473997 |
- Engage screed lock mechanism (5) on both sides of the machine.
Illustration 3 | g01510335 |
- Move screed lift switch (4) to the FLOAT position.
Note: The screed lift switch on the inactive instrument panel must also be in the FLOAT position in order to lower the screed.
- Move right screed extend switch (7) to the EXTEND position. Release the switch when the right screed extender is fully extended.
Illustration 4 | g01510336 |
- Move left screed extend switch (6) to the EXTEND position. Release the switch when the left screed extender is fully extended.
- Move throttle control switch (8) to the LOW IDLE position. Hold the switch in this position for less than 1 second.
Illustration 5 | g01510338 |
- After the engine reaches low idle, move engine start switch (9) to the OFF position.
- Install a small piece of reflective tape (10) from Tool (A) on the left conveyor bearing.
Illustration 6 | g01545436 |
- Move screed lift switch (4) to the HOLD position.
- Move engine start switch (9) to the START position. Release the engine start switch when the engine starts.
- Move throttle control switch (8) to the HIGH IDLE position. Hold the switch in this position for less than 1 second. The engine speed should increase to 2200 rpm.
- Monitor the hydraulic oil temperature on the operator display. Operate the machine until the oil temperature reaches 43 ± 5.6 °C (110 ± 10 °F).
Illustration 7 | g01513853 |
- Press home key (11) .
- Press down key (12) until "Service" is highlighted on the display screen.
Illustration 8 | g01510373 |
- Press OK key (13) .
- Press down key (12) until "Calibrations" is highlighted on the display screen.
Illustration 9 | g01510393 |
- Press OK key (13) .
- Press down key (12) until "Left Conveyor" is highlighted on the display screen.
Illustration 10 | g01513857 |
- Press OK key (13) .
- Press OK key (13) in order to begin the calibration.
- Move parking brake switch (1) to the ON position.
Illustration 11 | g01513859 |
- Move left conveyor switch (14) to the AUTO position.
Illustration 12 | g01513861 |
- Move left auger switch (15) to the AUTO position.
- Move propel mode switch (16) to the PAVE position.
Illustration 13 | g01510418 |
- Move propel lever (3) to the FORWARD position.
- Press OK key (13) .
- Rotate left conveyor speed dial (17) to the MINIMUM position.
Illustration 14 | g01513862 |
Illustration 15 | g01513867 |
- Press OK key (13) .
- Rotate left conveyor speed dial (17) clockwise until the left conveyor just begins to operate.
Illustration 16 | g01513871 |
- Press OK key (13) .
- Rotate left conveyor speed dial (17) clockwise until the speed of the left conveyor reaches 65 ± 3 rpm. Use Tool (A) to measure the speed.
Illustration 17 | g01513962 |
- Press OK key (13) .
- The display should now read "CALIBRATION COMPLETE". Push back key (18) to return to calibration screen.
Illustration 18 | g01513975 |
- Push home key (11) in order to exit the calibration screen.
- Move propel lever (3) to the NEUTRAL position.
- Move left conveyor switch (14) to the OFF position.
- Move left auger switch (15) to the OFF position.
- Move throttle control switch (8) to the LOW IDLE position. Hold the switch in this position for less than 1 second.
- After the engine reaches low idle, move engine start switch (9) to the OFF position.