Hydraulic System Oil Filter - Replace
Show/hide table
 |
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin. |
 |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
| NOTICE |
|---|
Take extreme care to insure the cleanliness of the hydraulic oil. Keep the hydraulic oil clean in order to extend the component life and assure the maximum performance. |
- Apply the parking brake. Turn the engine off.
- Slowly remove the hydraulic tank filler cap (1) in order to relieve the system pressure.
Show/hide table
 | |
| Illustration 1 | g00904299 |
- Open the engine access door on the right side of the machine.
Show/hide table
 | |
| Illustration 2 | g00899122 |
- Remove the filter element. Properly discard the filter element. Clean the filter element mounting base.
Show/hide table
 | |
| Illustration 3 | g00904303 |
- Apply a thin film of oil to the seal of the new oil filter.
- Install the new oil filter by hand. When the seal contacts the base, tighten the filter element for an additional three quarters of a turn.
- Start the engine. Allow the hydraulic oil to warm. Maintain the oil to the level mark on the sight gauge (2). If necessary, add oil.
- Close the engine access door.
Caterpillar Information System:
R1600 Load Haul Dump Machine Electrical System Electrical Power Supply
R1600 Load Haul Dump Machine Electrical System General Information
Bench Test Procedure for Hydraulic Piston Pumps{5070} Bench Test Procedure for Hydraulic Piston Pumps{5070}
3126B Engine for Caterpillar Built Machines Engine Pressure Sensor Open or Short Circuit - Test
CP-533C, CS-533C, CP-563C, CS-563C, CS-573C and CS-583C Vibratory Compactors Steering System Articulating and Oscillating Hitch
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Piston and Rings
TH220B, TH330B, TH340B, TH350B, TH355B, TH360B, TH460B, TH560B and TH580B Telehandlers MID 039 - CID 0444 - FMI 04
CB-434C Vibratory Compactor Hydraulic System Oil - Change
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Connecting Rod
2002/07/22 Special Instruction, REHS1115, "Procedure for the Installation of a Separate Brake Pump" {3108, 5056, 5070, 7306}
CB-434C Vibratory Compactor Fuses - Replace
2002/07/08 New Systems Operation, RENR6127, "IQAN Monitoring & Control System" is Available {7600}
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Braking and Hydraulic Fan System Pressure Sensor (Brake Charging)
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Braking and Hydraulic Fan System Limit Switch (Parking Brake)
TH220B, TH330B, TH340B, TH350B, TH355B, TH360B, TH460B, TH560B and TH580B Telehandlers MID 039 - CID 0490 - FMI 02
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Braking and Hydraulic Fan System Brake and Planetary
2002/11/18 New Adapters for the Shaw Aero Fast Fill Fuel Systems {1273, 1274, 1710}
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Braking and Hydraulic Fan System Solenoid Valve (Demand Fan)
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Braking and Hydraulic Fan System Parking Brake
2002/07/08 Special Instruction, REHS1022 , "Modification Procedure for Moving the Color Markng System from the Stick to the Harvester Head" is Available {6393}
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Braking and Hydraulic Fan System Pressure Sensor (Brake Oil)
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Braking and Hydraulic Fan System Solenoid Valve (Brake Charging)
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Braking and Hydraulic Fan System Solenoid Valve (Reversing Fan)
Computer Aided Bucking System (CABSWin/CABSDos) System Configuration (HH300/HH500/HH700) - CABSWin