Connecting Rod
Show/hide table
Illustration 1 | g00693257 |
(1) Connecting rod
(2) Piston pin bearing
- Clearance between the piston pin and the piston pin bearing (All models) ...
0.010 mm to 0.025 mm (0.00040 inch to 0.00099 inch)
- C0.5 and C0.7 ...
0.10 mm (0.004 inch)
Service limit
- C1.1/3011C and C1.6 ...
0.08 mm (0.0031 inch)
- C1.5/3013C, C2.2/3024C and C2.2/3024CT ...
0.10 mm (0.004 inch)
(3) Tighten the nut and bolt to the following torque.
- C0.5 and C0.7 ...
23 N·m (17 lb ft)
- C1.1/3011C and C1.6 ...
32 N·m (24 lb ft)
- C1.5/3013C, C2.2/3024C and C2.2/3024CT ...
52 N·m (38 lb ft)
(4) Connecting rod bearing
- Clearance between the connecting rod bore and the connecting rod bearing ...
0.10 mm to 0.30 mm (0.004 inch to 0.012 inch)
- Service limit ...
0.70 mm (0.0276 inch)
Markings on the Connecting Rod
Show/hide table
Illustration 2 | g00555416 |
Typical example |
The pistons and connecting rods are matched to each cylinder. Note the position of each connecting rod and piston for correct assembly.
Identification marks (1) on the connecting rod and on the connecting rod cap must be matched and aligned. When the connecting rod is installed correctly, the marks should face the right side of the engine.
Refer to Testing and Adjusting, "Connecting Rod - Inspect" for the procedure to measure distortion and parallelism of the connecting rod.
Caterpillar Information System:
2002/07/22 Special Instruction, REHS1115, "Procedure for the Installation of a Separate Brake Pump" {3108, 5056, 5070, 7306}
CB-434C Vibratory Compactor Fuses - Replace
2002/07/08 New Systems Operation, RENR6127, "IQAN Monitoring & Control System" is Available {7600}
CP-533C, CS-533C, CP-563C, CS-563C, CS-573C and CS-583C Vibratory Compactors Steering System Steering Control
3126B Engine for Caterpillar Built Machines 5 Volt Engine Pressure Sensor Supply Circuit - Test
2002/07/22 Use the Correct Torque for the Bolts that Secure the Belt Guard {1357, 7174}
R1700G Load Haul Dump Differential and Final Drive Oil Level (Without Axle Oil Cooler) - Check
R1700G Load Haul Dump Differential and Final Drive Oil Level (With Axle Oil Cooler) - Check
TH220B, TH330B, TH340B, TH350B, TH355B, TH360B, TH460B, TH560B and TH580B Telehandlers MID 039 - CID 0368 - FMI 04
CP-533C, CS-533C, CP-563C, CS-563C, CS-573C and CS-583C Vibratory Compactors Steering System Hydraulic Pump
CB-434C Vibratory Compactor Fuel Tank Water and Sediment - Drain
R1700G Load Haul Dump Differential and Final Drive Oil (Without Axle Oil Cooler) - Change
CB-434C Vibratory Compactor Hydraulic System Oil - Change
TH220B, TH330B, TH340B, TH350B, TH355B, TH360B, TH460B, TH560B and TH580B Telehandlers MID 039 - CID 0444 - FMI 04
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Piston and Rings
CP-533C, CS-533C, CP-563C, CS-563C, CS-573C and CS-583C Vibratory Compactors Steering System Articulating and Oscillating Hitch
3126B Engine for Caterpillar Built Machines Engine Pressure Sensor Open or Short Circuit - Test
Bench Test Procedure for Hydraulic Piston Pumps{5070} Bench Test Procedure for Hydraulic Piston Pumps{5070}
R1600 Load Haul Dump Machine Electrical System General Information
R1600 Load Haul Dump Machine Electrical System Electrical Power Supply
CB-434C Vibratory Compactor Hydraulic System Oil Filter - Replace
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Braking and Hydraulic Fan System Pressure Sensor (Brake Charging)
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Braking and Hydraulic Fan System Limit Switch (Parking Brake)
TH220B, TH330B, TH340B, TH350B, TH355B, TH360B, TH460B, TH560B and TH580B Telehandlers MID 039 - CID 0490 - FMI 02