C3.3 Industrial Engine Caterpillar

Connecting Rod - For Use With Spheroidal Graphite Iron (SGI) Crankshaft

Usage:

C3.3 E3J

Show/hide table




Illustration 1	g00907738

The mating surfaces of the connecting rod are produced by hydraulically fracturing the forged connecting rod.

(1) Tighten the torx screws for the connecting rod to the following torque. ... 18 N·m (13 lb ft)

Tighten the torx screws for the connecting rod again to the following torque. ... 70 N·m (52 lb ft)

Tighten the torx screws for the connecting rod for an extra 120 degrees. The torx screws for the connecting rod (1) must be replaced after this procedure.

Note: Always tighten the connecting rod cap to the connecting rod, when the assembly is out of the engine. Tighten the assembly to the following torque 20 N·m (14 lb ft).

(2) The bearing shell for the connecting rod

Show/hide table




Illustration 2	g00995584
Alignment of the bearing shell

Note: The bearing shell for the connecting rod must be aligned equally from both ends of the connecting rod. Refer to (A) in figure 2. Refer to the Disassembly and assembly manual for information on the alignment tool.

Show/hide table

Table 1
Bearing Width for the Connecting Rod	31.62 mm to 31.88 mm (1.245 inch to 1.255 inch)
Bearing Width for the Connecting Rod Cap	31.62 mm to 31.88 mm (1.245 inch to 1.255 inch)
Thickness of Connecting Rod Bearing at the Center	1.835 mm to 1.841 mm (0.0723 inch to 0.0725 inch)
Thickness of Connecting Rod Bearing for the Cap at the Center	1.835 mm to 1.841 mm (0.0722 inch to 0.0725 inch)
Bearing Clearance	0.034 mm to 0.081 mm (0.001 inch to 0.003 inch)

Show/hide table

Table 2
Undersized Connecting Rod Bearing
0.25 mm (0.010 inch)
0.51 mm (0.020 inch)
0.76 mm (0.030 inch)

Show/hide table




Illustration 3	g00907744

(3) Diameter of the parent bore for the piston pin ... 43.010 mm to 43.035 mm (1.693 inch to 1.694 inch)

(4) Distance between the parent bores ... 219.05 mm to 219.10 mm (8.624 inch to 8.626 inch)

(5) Diameter for the parent bore for the connecting rod bearing ... 67.208 mm to 67.221 mm (2.646 inch to 2.647 inch)

Show/hide table




Illustration 4	g00915056

Connecting rods are color coded. The color code is a reference for the length (Y) of the connecting rod. Refer to table 3 for the different lengths of connecting rods.

Show/hide table

Table 3
Length Grades for Connecting Rods
Grade Letter	Color Code	Length (Y)
F	Red	165.728 mm to 165.761 mm (6.524 inch to 6.526 inch)
G	Orange	165.682 mm to 165.715 mm (6.523 inch to 6.524 inch)
H	White	165.637 mm to 165.670 mm (6.521 inch to 6.522 inch)
J	Green	165.591 mm to 165.624 mm (6.519 inch to 6.521 inch)
K	Purple	165.545 mm to 165.578 mm (6.518 inch to 6.519 inch)
L	Blue	165.499 mm to 165.532 mm (6.516 inch to 6.517 inch)