Flywheel Housing - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 439-3940 | Bracket As | 2 |
Start By:
- Remove flywheel.
- Remove rear engine supports.
- Remove low-pressure turbocharger.
- Remove engine oil filter base.
- Remove auxiliary water pump.
- Remove fuel injection pump.
- Remove electric starting motor.
- Remove camshaft gear.
- Remove crankshaft rear seal.
- Install Tooling (A) to flywheel housing (6) and attach suitable lifting device. The weight of flywheel housing (6) is approximately
181 kg (39 lb) . Remove two bolts (1) and four bolts (2). Remove bolt (3). Remove ten bolts (4) and two bolts (5). Use suitable lifting device to remove flywheel housing (6).
Show/hide table
Illustration 1 | g06067294 |
- Install flywheel housing (6) in the reverse order of removal.
- Tighten two bolts (5) to a torque of
63 ± 6 N·m (46 ± 4 lb ft) . - Tighten ten bolts (4) to a torque of
63 ± 6 N·m (46 ± 4 lb ft) . - Tighten bolt (3) to a torque of
63 ± 6 N·m (46 ± 4 lb ft) . - Tighten four bolts (2) to a torque of
63 ± 6 N·m (46 ± 4 lb ft) . - Tighten two bolts (1) to a torque of
63 ± 6 N·m (46 ± 4 lb ft) .
- Tighten two bolts (5) to a torque of
Caterpillar Information System:
New Software Is Now Used on Certain C175-16 Engines {1920} New Software Is Now Used on Certain C175-16 Engines {1920}
G3516 TA Engine Data Link - Test
3512E Engines Exhaust Gas Valve (NRS) - Remove and Install
C12.9 Marine Engines Crankshaft - Remove and Install
A New Vertical Exhaust Elbow is Available for Certain 3512 and 3516 Marine Engines {1061} A New Vertical Exhaust Elbow is Available for Certain 3512 and 3516 Marine Engines {1061}
A New Duplex Oil Filter Control Plate Is Now Used For Certain C175 Engines {131D, 7557} A New Duplex Oil Filter Control Plate Is Now Used For Certain C175 Engines {131D, 7557}
A New Damper Is Used on Certain 3512C Tier 3 Marine Engines {1205} A New Damper Is Used on Certain 3512C Tier 3 Marine Engines {1205}
3516C Generator Set Engines Air Inlet Manifold - Remove and Install
Autonomous Stop (A-Stop) System Components
Autonomous Stop (A-Stop) General Information
Selective Catalytic Reduction Retrofit Aftertreatment Electronic Service Tools
G3512 Generator Set Engines Data Link - Test
G3512 Generator Set Engines Data Link Configuration Status - Test
New Engine Software for Certain C4.4 Generator Sets {7610, 7620} New Engine Software for Certain C4.4 Generator Sets {7610, 7620}
New Transmission Software Is Now Used for Certain CX31 On Highway Transmissions {7620} New Transmission Software Is Now Used for Certain CX31 On Highway Transmissions {7620}
320 GC, 320 and 323 Excavator Engine Air Filter Primary and/or Secondary Element - Replace
3516E Generator Set Coolant Level - Check
C12.9 Marine Engines Engine Support (Rear) - Remove and Install
C7.1 Marine Engine Engine Oil Filter Base - Remove and Install
C3.3 Industrial Engine Connecting Rod Bearing Journal - Spheroidal Graphite Iron Crankshaft
C4.4 Generator Sets Turbocharger
C3.3 Industrial Engine Main Bearing Journal - Spheroidal Graphite Iron (SGI) Crankshaft
C3.3 Industrial Engine Connecting Rod - For Use With Spheroidal Graphite Iron (SGI) Crankshaft
3512E Engines Venturi Tube - Remove and Install