Engine Oil Pan - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | - | Loctite SuperFlex 596 High Temp RTV Silicone Adhesive - Red | - |
Start By:
- Remove engine.
- Drain the engine oil and filter. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the proper draining and filling procedures.
Show/hide table
Illustration 1 g03785825 - Remove bolts (4), studs (6), and the fasteners.
- Remove clip (3) and clip (5). Position harness assembly (2) out of the way.
- Remove engine oil pan (1). Remove and discard the isolation seal.
Show/hide table
Illustration 2 g03785976 - Remove bolts (8) and bolts (9). Remove suction bell assembly (7).
Show/hide table
Illustration 3 g03786009 - Remove plugs (10).
- Install engine oil pan (1) in the reverse order of removal.
Show/hide table
Illustration 4 g02466177 Note: Ensure that the oil pan and mating surfaces are clean and free of oil.
- Apply Tooling (A) at four locations marked (A). Tooling (A) should be applied in
4.0 ± 1.0 mm (0.16 ± 0.04 inch) diameter beads.Note: All joints using Tooling (A) must be assembled within 10 minutes of the application.
- Tighten plugs (10) to a torque of
90 ± 15 N·m (66 ± 11 lb ft) .Show/hide tableIllustration 5 g02466597 Torque Sequence - Tighten bolts (3) and stud bolts (2) in the above sequence.
- Tighten plugs (10) to a torque of
Caterpillar Information System:
C2.2 Engines for Caterpillar Built Machines Temperature Sensor (Exhaust)
C7.1 Engines DEF Line Heater - Test
C2.2 Engines for Caterpillar Built Machines Temperature Sensor (DOC Inlet)
C2.2 Engines for Caterpillar Built Machines Belt Tension Chart
794 AC Off-Highway Truck Engine Supplement Hood - Remove and Install
C7.1 Engines DEF Control Module Power - Test
C7.1 Engines Data Link Configuration Status - Test
C13 Generator Set Engine Alternator - Remove and Install
2015/01/16 Cat® Reman Announces the Availability of Remanufactured Engines for Certain Electric Power Generation Applications {1000}
C13 Generator Set Engine Vibration Damper and Pulley - Remove and Install
C13 Generator Set Engine Flywheel - Remove and Install
C13 Generator Set Engine Air Control Valve - Remove and Install
3512E Engines Water Temperature Regulators - Remove and Install - Jacket Water
3512E Engines Water Temperature Regulators - Remove and Install - SCAC
Field Procedure to Adjust the Steering Shaft on Certain Off-Highway Trucks{4310, 4343} Field Procedure to Adjust the Steering Shaft on Certain Off-Highway Trucks{4310, 4343}
2015/02/06 A New Special Instruction is Available to Adjust the Steering Shaft on Certain Off-Highway Trucks {4310}
C13 Generator Set Engine Exhaust Elbow - Remove and Install
C3.4B Engines NRS Mass Flow Rate Problem
C2.2 Engines for Caterpillar Built Machines Rocker Shaft
C2.2 Engines for Caterpillar Built Machines Valve Mechanism Cover
C15 Generator Set Rotating Rectifier - Inspect/Test
C7.1 Engines DEF Pump Motor - Test
G3500H 60Hz Generator Sets Overhaul (Major)
New O-Ring Seals Are Available for Ignition Coil Extenders on Certain G3500 and G3600 Engines {1550, 1561} New O-Ring Seals Are Available for Ignition Coil Extenders on Certain G3500 and G3600 Engines {1550, 1561}