Water Temperature Regulators - Remove and Install - SCAC
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Drain the coolant. Refer to Operation and Maintenance Manual, "Coolant - Change" for the correct draining and filling procedures.
Show/hide table
Illustration 1 g03786061 - Remove tube assembly (1). Remove the O-ring seals.
Show/hide table
Illustration 2 g03786062 - Disconnect hose from elbow (2). Remove and discard bellows assembly (3).
Show/hide table
Illustration 3 g03786063 Show/hide table
Illustration 4 g03786064 - Loosen bolt (4). Bolt (4) will remain in water temperature regulator housing (6).
- Remove bolts (5) and remove water temperature regulator housing (6).
Show/hide table
Illustration 5 g03786097 - Remove O-ring seal (7) and remove water temperature regulator (8). Repeat for the remaining water temperature regulators.
- Install water temperature regulator (8) in the reverse order of removal.
- Install new bellows (3) and tighten the clamps to a torque of
12 ± 1 N·m (106 ± 9 lb in) .
- Install new bellows (3) and tighten the clamps to a torque of
Caterpillar Information System:
3512E Engines Water Temperature Regulators - Remove and Install - Jacket Water
C13 Generator Set Engine Engine Oil Pan - Remove and Install
C2.2 Engines for Caterpillar Built Machines Temperature Sensor (Exhaust)
C7.1 Engines DEF Line Heater - Test
C2.2 Engines for Caterpillar Built Machines Temperature Sensor (DOC Inlet)
C2.2 Engines for Caterpillar Built Machines Belt Tension Chart
794 AC Off-Highway Truck Engine Supplement Hood - Remove and Install
C7.1 Engines DEF Control Module Power - Test
C7.1 Engines Data Link Configuration Status - Test
C13 Generator Set Engine Alternator - Remove and Install
2015/01/16 Cat® Reman Announces the Availability of Remanufactured Engines for Certain Electric Power Generation Applications {1000}
C13 Generator Set Engine Vibration Damper and Pulley - Remove and Install
Field Procedure to Adjust the Steering Shaft on Certain Off-Highway Trucks{4310, 4343} Field Procedure to Adjust the Steering Shaft on Certain Off-Highway Trucks{4310, 4343}
2015/02/06 A New Special Instruction is Available to Adjust the Steering Shaft on Certain Off-Highway Trucks {4310}
C13 Generator Set Engine Exhaust Elbow - Remove and Install
C3.4B Engines NRS Mass Flow Rate Problem
C2.2 Engines for Caterpillar Built Machines Rocker Shaft
C2.2 Engines for Caterpillar Built Machines Valve Mechanism Cover
C15 Generator Set Rotating Rectifier - Inspect/Test
C7.1 Engines DEF Pump Motor - Test
G3500H 60Hz Generator Sets Overhaul (Major)
New O-Ring Seals Are Available for Ignition Coil Extenders on Certain G3500 and G3600 Engines {1550, 1561} New O-Ring Seals Are Available for Ignition Coil Extenders on Certain G3500 and G3600 Engines {1550, 1561}
3512E Engines Water Pump - Remove and Install
2015/02/27 A New Intake Plenum Plate Assembly Is Used on G3508B and G3516B Petroleum Engines {1094}