Aftercooler - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 189-0410     | 钩环组件     | 2     |
开始:
- 拆下风扇。 请参阅拆解和组装, "风扇 - 拆卸和安装"。
- 将冷却液从冷却系统中排入合适的容器,以便保存或弃置。 请参阅操作和保养手册, "冷却系统冷却液(ELC)- 更换"。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
- 拆下卡箍 (1) 。 对另一侧重复此操作。
Show/hide table
图 1 | g01290908 |
- 断开底部后冷器管 (2) 。
Show/hide table
图 2 | g01290915 |
- 断开顶部散热器软管 (3) 。
Show/hide table
图 3 | g01290916 |
- 断开顶部后冷器管 (4) 。
Show/hide table
图 4 | g01290917 |
- 断开底部散热器软管 (5) 。 断开底部后冷器管 (6) 。
Show/hide table
图 5 | g01290930 |
- 将软管组件 (8) 从燃油冷却器 (7) 上断开。
Show/hide table
图 6 | g01290934 |
- 将软管组件 (9) 从燃油冷却器 (7) 上断开。
Show/hide table
图 7 | g01290939 |
- 拆下螺栓 (10) 。 拆下螺栓 (11) 。
Show/hide table
图 8 | g01294215 |
- 将工具 (A) 和适当的起吊设备固定到后冷器 (12) 上。 后冷器 (12) 的重量约为 227 kg (500 lb)。
Show/hide table
图 9 | g01294232 |
- 拆下螺栓 (13) 。 将螺栓 (14) 和 (15) 从后冷器 (12) 上拆下。
Show/hide table
图 10 | g01294234 |
- 对于另一侧重复步骤 9 至步骤 11。
- 折下后冷器 (12) 。
Caterpillar Information System:
C15 On-Highway Engine Clean Gas Induction Cooler - Remove and Install
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Silicon Controlled Rectifiers - Test
C15 On-Highway Engine Fuel Pressure Sensor - Remove and Install - ARD Main Fuel Pressure Sensor
C15 On-Highway Engine Fuel Pressure Sensor - Remove and Install - ARD Pilot Fuel Pressure Sensor
3500C Marine Auxiliary Engines Factory Passwords
C15 On-Highway Engine Boost Pressure Sensor - Remove and Install
C15 On-Highway Engine Inlet Air Temperature Sensor - Remove and Install
C15 On-Highway Engine Inlet Manifold Temperature Sensor - Remove and Install
3516C Locomotive Engine Closed Crankcase Ventilation (CCV) Fumes Disposal Filter - Replace
C15 On-Highway Engine Engine Control Module - Remove and Install
C15 On-Highway Engine Air Compressor - Remove and Install
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys K1 Overcurrent Shutdown - Reset
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Emergency Power Off - Reset
C15 On-Highway Engine Inlet and Exhaust Valve Springs - Remove and Install
2006/08/07 Marine Engines are Shipped Without Oil {1348}
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Log File - Retrieve
2006/08/07 A New O-ring is Now Used {1063, 1380}
C13 and C15 On-highway Engines Kickout Bypass - Test
C13 and C15 On-highway Engines Power Take-Off - Test
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Data - Capture
3612 and 3616 Engines Crankshaft Front Seal - Remove
3612 and 3616 Engines Crankshaft Front Seal - Install
TA19-M2WD and TA19-M4WD Agricultural Transmissions Daily Inspection
3612 and 3616 Engines Crankshaft Rear Seal - Remove