Crankshaft Front Seal - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
B     | 8T-0914 (1)     | 导向销     | 2     |
C     | -     | 导向螺栓 3/8 - 16 × 5 in     |
2     |
D     | 1P-0808     | 多功能润滑脂     | -     |
Show/hide table
( 1 ) | 9U-5105 发动机工具总成 中的零件 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 在曲轴前端安装工具 (B) 。
注: 适配器 (4) 内套筒上的对正标记必须与曲轴上的对正标记对齐。
Show/hide table
图 1 | g01294394 |
- 将适当的起吊设备连接到接头 (4) 上。 接头 (4) 的重量约为 70 kg (154 lb)。 将适配器 (4) 在工具 (B) 上放置到位。 安装将适配器 (4) 固定到位的螺栓 (3) 。
- 拆下工具 (B) 。
- 将工具 (C) 安装到前壳体中。
注: 必须将曲轴前油封连同密封唇朝向发动机内侧安装。 确保曲轴的每一端都安装了正确的密封。
- 将工具 (D) 施加在适配器 (1) 外径的 O 形密封圈上。
- 将曲轴前油封和适配器 (1) 置于工具 (C) 上。 将曲轴前油封和适配器 (1) 小心地滑到前壳体上。
注: 确保所有零件都是清洁的。 不要触摸密封唇。 不要在密封唇上使用润滑剂。 确保油封上的箭头与曲轴转向指向同一方向。
- 安装将曲轴前油封和适配器 (1) 固定入位的螺栓 (2) .。
End By: 安装减振器。 请参考 拆解和组装, "减振器 - 安装"。
Caterpillar Information System:
3612 and 3616 Engines Crankshaft Front Seal - Remove
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Data - Capture
C13 and C15 On-highway Engines Power Take-Off - Test
C13 and C15 On-highway Engines Kickout Bypass - Test
2006/08/07 A New O-ring is Now Used {1063, 1380}
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Log File - Retrieve
2006/08/07 Marine Engines are Shipped Without Oil {1348}
C15 On-Highway Engine Inlet and Exhaust Valve Springs - Remove and Install
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Emergency Power Off - Reset
C27 and C32 Generator Set Engines Aftercooler - Remove
C15 On-Highway Engine Clean Gas Induction Cooler - Remove and Install
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Silicon Controlled Rectifiers - Test
TA19-M2WD and TA19-M4WD Agricultural Transmissions Daily Inspection
3612 and 3616 Engines Crankshaft Rear Seal - Remove
3612 and 3616 Engines Crankshaft Rear Seal - Install
C13 and C15 On-highway Engines Shutdown (PTO) - Test
C13 and C15 On-highway Engines Shutdown Timer (Idle) - Test
C7 Engines for Caterpillar Built Machines Valve Mechanism
C13 and C15 On-highway Engines Speed Control (PTO) - Test
3612 and 3616 Engines Crankshaft Front Gear - Remove and Install
3612 and 3616 Engines Crankshaft Rear Gear - Remove and Install
3508B, 3512B, and 3516B High Displacement Generator Sets Monitoring System
C13 and C15 On-highway Engines Starting Aid - Test
C13 and C15 On-highway Engines Tachometer - Test