Rocker Shaft and Pushrod - Install
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 8T-2998     | Lubricant     | 1     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Apply Tooling (A) to both ends of push rods (7) .
Show/hide table
Illustration 1 | g01262209 |
- Lubricate push rods (7) with clean engine oil. Install push rods (7) .
- Install valve bridges (6) with the knob on top of valve bridge positioned away from the rocker shaft and the bevel end of the valve bridge positioned closest to the rocker shaft.
- Position rocker shaft (3) . Install bolts (1) and (2) . Finger tighten bolts (1) and (2) . Tighten bolts (1) to a torque of 100 ± 20 N·m (74 ± 15 lb ft). Tighten bolts (2) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Show/hide table
Illustration 2 | g01262208 |
- Apply Tooling (A) to each of the button faces of the rocker arms.
- Adjust the valve lash of the rocker arm by turning rocker arm adjustment screws (5) . Refer to Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust".
End By: Install the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve Mechanism Cover Base - Remove and Install".
Caterpillar Information System:
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 3825 - FMI 8
C7 On-Highway Engine Rocker Shaft and Pushrod - Remove
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 191 - FMI 8
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 161 - FMI 8
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 3027 - FMI 3
C7 On-Highway Engine Connecting Rod Bearings - Install
C7 On-Highway Engine Connecting Rod Bearings - Remove
C7 On-Highway Engine Pistons and Connecting Rods - Install
C7 PETROLEUM Petroleum Engine Air Inlet Heater - Remove and Install
2006/04/17 A New Impeller is Now Used in the Sea Water Pump of Marine Engines {1371}
3500B Industrial Engines with the ADEM 3 Electronic Control Module System Overview
C7 On-Highway Engine Pistons and Connecting Rods - Assemble
C7 PETROLEUM Petroleum Engine Water Temperature Regulator - Remove and Install
CX28 On-Highway Transmission Drive Plate
C7 and C9 On-highway Engines Emissions Certification Film
CX31 On-Highway Transmission Oil Filter (Transmission)
C7 On-Highway Engine Fuel Injection Pump - Remove
C7 On-highway Engine Air Lines - Aftertreatment Regeneration Device
3500B Industrial Engines with the ADEM 3 Electronic Control Module Electrical Connectors and Functions
725C, 725C2, 730C, 730C2 and 730C, 730C2 EJECTOR Articulated Truck Systems Gear Pump (Transmission)
C11 and C13 Petroleum Engines Rocker Arm - Disassemble
C11 and C13 Petroleum Engines Rocker Arm - Assemble
C9 On-highway Engine Engine Oil Pan
C7 On-Highway Engine Lifter Group - Remove and Install