Maintenance Parameters
"保养指示模式"
发动机控制模块 (ECM) 记录与车辆保养有关的数据。 如果选择的是距离，维修工具上的所有保养指示都以距离为单位显示。 通常的保养指示为 PM 1、PM 2 和冷却系统清洗/冲洗。
如果选择的是小时数，维修工具上的所有保养指示都以小时数为单位显示。 通常的保养指示为 PM 1、PM 2 和冷却系统清洗/冲洗。 ECM 提供 PM 1 保养周期和上一次的保养信息。
Show/hide table
| 可选方案 | 缺省值 |
| "手动距离" "手动小时数" "自动距离" "自动小时数" |
"断开" |
"PM 1 周期"
"PM 1 周期"允许客户指定保养周期 (PM 1)。 只有当"保养指示器模式"被设为手动模式（距离或小时数）时才能设置此参数（"PM 1 周期"）。
Show/hide table
| 手动距离 | ||
| 最小值 | 最大值 | 缺省值 |
8050 km (5000 英里) |
56325 km (35000 英里) |
24140 km (15000 英里) |
Show/hide table
| 手动小时数 | ||
| 最小值 | 最大值 | 缺省值 |
| 100 | 750 | 300 |
"发动机机油容量"
"PM 1 周期"可由 ECM 规定。 ECM 会根据燃油使用情况确定 "PM 1 周期"。 只有当 "保养指示器模式"被设为自动模式（距离或小时数）时才能设置此参数（"发动机机油容量"。 油槽容量会影响保养周期。
Show/hide table
| 最小值 | 最大值 | 缺省值 |
19 L (20 qt) |
57 L (60 qt) |
参见表 5。 |
Show/hide table
| 发动机型号 | 缺省值 |
| C11和 C13 | 34 L (36 qt) |
| C15 | 38 L (40 qt) (1) |
Show/hide table
| ( 1 ) | 带前油底壳BrakeSaver的 C15发动机应该设为49 L (52 qt)。 |
Caterpillar Information System:
C4.4 Industrial Engine Increased Engine Oil Temperature - Inspect
C11 and C13 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
Instructions for Installation of the 240-5916 Repair Kit (Muffler Clamp) {1062} Instructions for Installation of the 240-5916 Repair Kit (Muffler Clamp) {1062}
G3500B Engines Electronic Service Tools
C11 and C13 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
C11, C13, and C15 On-highway Engines California Emission Control Warranty Statement
G3520C and G3520E Generator Set Engines Engine Sensors
C11 and C13 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
3408C and 3412C Marine Auxiliary and Marine Generator Set Engines Reference Material
G3520C and G3520E Generator Set Engines Integrated Temperature Sensing Module
C11 and C13 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
C11, C13, and C15 On-highway Engines Federal Emission Control Warranty
2003/10/01 An Improved Alternator Belt is Used {1357}
G3406 Engines Water Temperature Regulator
SPP101 Skid Mounted Pumper Maintenance Interval Schedule
G3520B Engines Engine Overcrank
3500B and 3500C Marine Engines Engine Governing - Adjust
C3.3 Industrial Engine Cylinder Block - Inspect
SPP101 Skid Mounted Pumper Model View Illustrations
G3406 Engines Ignition Transformer
2003/08/01 A Previous High Temperature Locknut is Used in Engine Exhaust System Groups {7553}
SPP101 Skid Mounted Pumper Engine Crankcase Breather - Clean
C11 and C13 Engines for Caterpillar Built Machines Crankshaft - Remove
C15 On-highway Engine Inlet and Exhaust Valve Seat Inserts - Remove and Install