Air Starting Motor - Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 有几种不同的气动马达可供使用。 根据不同的气管组件起动马达的配置也不同。 下面是安装两个不同气动马达的示例。
- 将适当起吊设备连在气动马达 (6)上。 气动马达 (6)的重量约为
48 kg (106 lb) . - 在气动马达盖 (6)和飞轮壳体间的接头上安装一个新密封垫。 定位气动马达 (6)。 安装螺栓 (7).
- 连接软管组件 (5)。
Show/hide table
图 2 g00597642 - 安装管组件 (4)和U形螺栓 (3)。
- 安装螺栓 (2).
- 连接软管组件 (1)。
Show/hide table
图 1 | g00597643 |
- 将适当起吊设备连在气动马达 (4)上。 带气管组件的气动马达 (4)的重量约为
86 kg (190 lb) 。 - 在气动马达盖 (4)和飞轮壳体间的接头上安装一个新密封垫。 定位气动马达 (4)。 安装螺栓 (3).
Show/hide table
图 4 g00615939 - 将管与弯管 (2)连接。
- 连接线束组件 (1)。
Show/hide table
图 3 | g00615940 |
Caterpillar Information System:
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Cylinder Head - Install
G3606 and G3608 Engines Actuator (Hydrax) - Remove
G3500 Engines Gas Pressure Regulator Solenoid - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 333 FMI 4 Alarm Module Control Voltage Below Normal - Test
G3500 Engines Fuel Control Valve - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 333 FMI 3 Alarm Module Control Voltage Above Normal - Test
3500B Engines and 3500 Engines with EUI Option Engine Control Switch (ECS)
G3500 Engines Fuel Control Actuator - Remove and Install
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 331 FMI 2 Switch (Engine Control) Incorrect Signal - Test
G3500 Engines Electronic Sensor - Remove and Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Gear Group (Front)
G3500 Engines Carburetor - Assemble - High Pressure
3500B Engines Air Starting Motor - Disassemble
G3500 Engines Gas Pressure Regulator - Remove - Low Pressure
G3500 Engines Gas Pressure Regulator - Install - Low Pressure
G3500 Engines Gas Pressure Regulator - Remove - High Pressure
345B Excavator and 345B Material Handler Machine System Specifications Solenoid Valve (Counterweight Control)
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 336 FMI 2 Switch (Engine Control) Incorrect Signal - Test
G3500 Engines Gas Pressure Regulator - Install - High Pressure
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 441 FMI 12 Oil Step Relay Failed - Test
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Install - 3003 Engine
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Remove - 3003 Engines
3126B Marine Engine Alternator and Regulator
G3500 Engines Gas Pressure Regulator - Disassemble