Air Starting Motor - Disassemble
Show/hide table
需要的工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 1P-1854 | 挡圈钳 | 1 |
B | 钢板
50.8 mm (2 inches) x 102 mm (4 inches) x 6 mm (0.25 inches) |
1 | |
C | 1P-1857 | 挡圈钳 | 1 |
开始:
- 拆卸气动马达。 参考拆解与组装 , "气动马达 - 拆卸 "。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 有几种不同的气动马达可供使用。 下面是一个典型气动马达拆解的示例。
注: 解体气动马达前,必须准备好这些零件的完整套件: 密封垫, O形密封圈 , 密封件 和 叶片。
- 从马达壳体 (3)拆卸弯管 ( 1)和支架 (2)。
Show/hide table
图 2 g00597694 - 为确保正确组装,标记与齿轮箱 ( 6)相关的马达壳体 ( 3)的位置。 拆卸螺栓 ( 4)。 整体同时拆下齿轮箱 ( 6)和驱动器壳体 (5)。
Show/hide table
图 3 g00597696 - 使用工具 (A)从传动器齿轮 ( 7)上拆卸密封圈 (8)。
Show/hide table
图 4 g00597697 注: 螺栓 (9)具有左手螺纹。
- 拆卸螺栓 (9)和垫圈 ( 10)。 拆卸销小齿轮 ( 11)、衬套和弹簧。
为确保正确组装,标记与齿轮箱 ( 6)相关的驱动器壳体 ( 5)的位置。 从齿轮箱 ( 6)上拆卸螺栓 (12)和驱动器壳体 ( 5)。
Show/hide table图 5 g00597698 - 从驱动器壳体 (5)上拆卸O形密封圈 ( 13)。
Show/hide table
图 6 g00597701 Show/hide table驱动器轴、活塞和传动齿轮都受到弹簧力的作用。 拆卸这些组件前缓慢地释放弹簧力。
- 将工具 (B)放在传动齿轮 ( 7)和活塞 (14)之间。 使用合适的夹具以压缩回动弹簧。 拆卸将驱动轴和活塞固定在驱动器壳体 ( 5)上的定位环。
Show/hide table
图 7 g00597709 Show/hide table被弹簧力爆出的零件击中,会招致人员伤害。
确保穿上所有必要的保护装备。
遵照建议的程序,并使用所有建议的工具以释放弹簧力。
- 缓慢地释放压力以消除回动弹簧 ( 16)力。 拆卸工具 (B)。 拆卸密封圈 (15)。 整体同时从壳体 (5)上将传动齿轮、活塞和驱动轴拆下。 拆卸回动弹簧 (16)。
Show/hide table
图 8 g00597711 - 松开螺栓(未显示)直到螺栓可自由活动。 整体同时从传动齿轮上 ( 7)将驱动轴 (17)和活塞 ( 14)拆下。
Show/hide table
图 9 g00597712 - 从活塞 (14)上拆下隔板 ( 18)。
Show/hide table
图 10 g00597713 - 从隔板 (18)上拆卸O形密封圈 ( 19)。
Show/hide table
图 11 g00597714 - 从活塞 (14)上拆卸环 ( 20)。 从驱动轴 (17)上拆卸活塞。
Show/hide table
图 12 g00597715 - 从活塞 (14)上拆卸O形密封圈 ( 22)和密封件 (21)。
Show/hide table
图 13 g00597716 Show/hide table被弹簧力爆出的零件击中,会招致人员伤害。
确保穿上所有必要的保护装备。
遵照建议的程序,并使用所有建议的工具以释放弹簧力。
- 从驱动轴 (17)上拆卸以下零件: 挡圈 (31) , 杯形座 (30) , 弹簧 (29) , 驱动器离合器爪 ( 28), 驱动器离合器爪 ( 27), 轴承 (26) , 垫圈 (25) , 锁紧垫圈 (24) 和 螺栓 (23) 。
Show/hide table
图 14 g00597717 注: 如果环 (32)被拆下,组装时需要用一个新环。
- 从驱动轴 (17)上拆卸密封圈 ( 32)和轴承 (33)。
Show/hide table
图 15 g00597719 - 使用工具 (C)拆卸活塞环 ( 35)。 从齿轮箱 (6)上拆卸轴承 ( 34)。
Show/hide table
图 16 g00597722 - 从驱动器壳体 (5)上拆卸弹簧座 ( 36)和轴承 (37)。
Show/hide table
图 17 g00597723 - 从驱动器壳体 (5)上拆卸密封件 ( 38)。
Show/hide table
图 18 g00597724 - 为确保正确组装,标记与马达壳体 ( 3)相关的盖 (39)的位置。 从马达壳体 (3)上拆卸盖 ( 39)和O形密封圈。
Show/hide table
图 19 g00597725 - 从马达壳体的转子上拆卸螺栓 ( 41)和转子小齿轮 (40)。
Show/hide table
图 20 g00597726 - 松开螺栓 (43)和拆卸螺母 ( 42)。 从后端面板 (45)上拆卸轴承 ( 44)。
Show/hide table
图 21 g00597727 - 拆卸O形密封圈 (46)和后端面板 ( 45)。
Show/hide table
图 22 g01054297 - 从转子 (48)上拆卸叶片 ( 47)。
Show/hide table
图 23 g00597729 - 从马达壳体 (3)上拆卸转子 ( 48)。
Show/hide table
图 24 g00597730 - 使用合适的夹具从转子 ( 48)上将轴承 (49)和前端面板 ( 50)作为整体拆卸。
Show/hide table
图 25 g00597731 - 从前端面板 (50)上拆卸轴承 ( 49)。
Show/hide table
图 26 g00597732 - 从前端面板 (50)上拆卸垫圈 ( 51)。
Show/hide table
图 27 g00597734 - 从转子芯 (53)上拆卸O形密封圈 ( 52) 。
Show/hide table
图 28 g01005075 - 从马达壳体 (3)上拆卸转子芯 ( 53)。 从转子芯 (53)上拆卸O形密封圈 ( 54)。
Show/hide table
图 1 | g00597693 |
Caterpillar Information System:
3500B Engines Air Starting Motor - Install
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Cylinder Head - Install
G3606 and G3608 Engines Actuator (Hydrax) - Remove
G3500 Engines Gas Pressure Regulator Solenoid - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 333 FMI 4 Alarm Module Control Voltage Below Normal - Test
G3500 Engines Fuel Control Valve - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines CID 333 FMI 3 Alarm Module Control Voltage Above Normal - Test
3500B Engines and 3500 Engines with EUI Option Engine Control Switch (ECS)
G3500 Engines Fuel Control Actuator - Remove and Install
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 331 FMI 2 Switch (Engine Control) Incorrect Signal - Test
G3500 Engines Electronic Sensor - Remove and Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Gear Group (Front)
G3500 Engines Gas Pressure Regulator - Remove - Low Pressure
G3500 Engines Gas Pressure Regulator - Install - Low Pressure
G3500 Engines Gas Pressure Regulator - Remove - High Pressure
345B Excavator and 345B Material Handler Machine System Specifications Solenoid Valve (Counterweight Control)
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 336 FMI 2 Switch (Engine Control) Incorrect Signal - Test
G3500 Engines Gas Pressure Regulator - Install - High Pressure
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 441 FMI 12 Oil Step Relay Failed - Test
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Install - 3003 Engine
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Remove - 3003 Engines
3126B Marine Engine Alternator and Regulator
G3500 Engines Gas Pressure Regulator - Disassemble
3126B Marine Engine Alternator and Regulator