Centershift Lock Bar and Bushings - Remove
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 1U-9200     | Lever Puller Hoist     | 1     |
B     | 123-3804     | Bearing Puller Adapter     | 1     |
1U-7758 | Stud     | 1     | |
9U-6832 | Nut     | 1     | |
4K-0684 | Hard Washer     | 1     | |
6V-3170 | Double Acting Cylinder     | 1     | |
350-7768 | Electric Hydraulic Pump Gp (115V)     | 1     | |
350-7769 | Electric Hydraulic Pump Gp (230V)     | 1     | |
5F-7693 | Spacer As     | 1     | |
C     | 1P-1832     | Adapter     | 1     |
5P-4776 | Tool Stud     | 1     | |
9U-6833 | Nut     | 1     | |
5P-8250 | Washer     | 1     | |
6V-3160 | Double Acting Cylinder     | 1     | |
350-7768 | Electric Hydraulic Pump Gp (115V)     | 1     | |
350-7769 | Electric Hydraulic Pump Gp (230V)     | 1     | |
5F-7693 | Spacer As     | 1     |
Start By:
- Connect the steering frame lock.
Show/hide table
When you are using hydraulic cylinders and puller studs, always ensure that the rated capacity of the puller stud meets or exceeds the rated capacity of the hydraulic cylinder. If the puller stud does not meet or exceed the rated capacity of the hydraulic cylinder, a sudden failure of the puller stud could occur. The sudden failure of the puller stud could result in personal injury or death. |
- Lower the blade to the ground. Retract the centershift lock pin. Refer to Operation and Maintenance Manual, "Centershift Lock" for the correct procedure.
- Attach Tooling (A) and a suitable lifting device to blade lift arms (1) .
Show/hide table
Illustration 1 | g01397540 |
Typical Example |
- Attach a suitable lifting device to centershift cylinder (2). The weight of centershift cylinder (2) is approximately 54 kg (120 lb).
Show/hide table
Illustration 2 | g01397553 |
- Remove bolts (3) and cap (4) .
Note: Note the shims for installation purposes.
- Use the machine to retract the cylinder rod. Lower centershift cylinder (2) to drawbar (5) .
- Release the system pressure.
- Attach a suitable lifting device to centershift lock bar (8). The weight of centershift lock bar (8) is approximately 77 kg (170 lb).
Show/hide table
Illustration 3 | g01397593 |
- Remove bolts (6) and lock (9). Repeat this step for the opposite side.
- Remove pin (7). Lower centershift lock bar (8) to the drawbar.
- Attach a suitable lifting device to opposite side of centershift lock bar (8) .
Show/hide table
Illustration 4 | g01397600 |
- Remove pin (10) and lower centershift lock bar (8) to the drawbar.
- Remove seals (11) .
Note: Note the orientation of seals (11) for assembly purposes.
Show/hide table
Illustration 5 | g01397601 |
- Use Tooling (B) to remove bearing (12) .
Show/hide table
Illustration 6 | g01397603 |
Show/hide table
Illustration 7 | g01397605 |
- Use Tooling (C) to remove bushings (13) .
Caterpillar Information System:
MH3049 Material Handler Hydraulic System Main Control Valve Air - Purge
559C, 579C, 2384C, and 2484C Knuckleboom Loaders TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565} 559C, 579C, 2384C, and 2484C Knuckleboom Loaders TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565}
730C2 and 725C2 Articulated Truck Power Train Transmission Planetary - Assemble
349F and 352F Excavator Machine System Electrical Connector - Inspect
730C2 and 725C2 Articulated Truck Power Train Transmission Planetary - Disassemble
559C and 579C Knuckleboom Loaders Connector Locations
349F and 352F Excavators Determining Diagnostic Trouble Codes
990K Wheel Loader Alternate Exit
559C and 579C Knuckleboom Loaders General Information
2012/07/25 A New Alternator Harness Is Now Used on the AP500E Asphalt Paver {1406, 1408}
2012/08/07 New Bearing Group and Clevis Pin Is Now Used on AS4252C Screeds {5639, 5641}
2012/07/31 New Support Group Blade Now Used on AS4252C Screeds {6656}
12M Motor Grader Machine Systems Centershift Lock Bar and Bushings - Install
12M Motor Grader Machine Systems Centershift Lock - Remove and Install
R1600H Load Haul Dump Power Train System Schematic
2012/08/08 A New Air Conditioner Relay is Now Available for Certain Load Haul Dump Machines {7320}
2012/08/08 A New Air Conditioner Relay is Now Available for Certain R1300G Load Haul Dump Machines {7320}
C27 and C32 Engines for Caterpillar Built Machines Piston and Rings
C27 and C32 Engines for Caterpillar Built Machines Exhaust Manifold
16M Series 3 and 18M Series 3 Motor Graders Fuel Tank Water and Sediment - Drain
3516B and 3516C Engines For MT4400D AC Off-Highway Trucks Data Link - Test
12M Motor Grader Machine Systems Centershift Lock - Disassemble
12M Motor Grader Machine Systems Centershift Lock - Assemble
12M Motor Grader Machine Systems Blade Lift Arm - Remove