Centershift Lock Bar and Bushings - Install
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 1U-9200     | Lever Puller Hoist     | 1     |
D     | 1P-0510     | Driver Gp     | 1     |
E     | 1P-1836     | Bearing Puller Adapter     | 1     |
1U-7758 | Stud     | 1     | |
9U-6832 | Nut     | 1     | |
4K-0684 | Hard Washer     | 1     | |
6V-3170 | Double Acting Cylinder     | 1     | |
350-7768 | Electric Hydraulic Pump Gp (115V)     | 1     | |
350-7769 | Electric Hydraulic Pump Gp (230V)     | 1     | |
5P-4197 | Spacer     | 1     | |
F     | 123-3804     | Bearing Puller Adapter     | 1     |
1U-7758 | Stud     | 1     | |
9U-6832 | Nut     | 1     | |
4K-0684 | Hard Washer     | 1     | |
6V-3170 | Double Acting Cylinder     | 1     | |
350-7768 | Electric Hydraulic Pump Gp (115V)     | 1     | |
350-7769 | Electric Hydraulic Pump Gp (230V)     | 1     |
Show/hide table
When you are using hydraulic cylinders and puller studs, always ensure that the rated capacity of the puller stud meets or exceeds the rated capacity of the hydraulic cylinder. If the puller stud does not meet or exceed the rated capacity of the hydraulic cylinder, a sudden failure of the puller stud could occur. The sudden failure of the puller stud could result in personal injury or death. |
- Use Tooling (D) to install seals (11) .
Show/hide table
Illustration 1 | g01397601 |
- Use Tooling (F) to install bearing (12) .
Show/hide table
Illustration 2 | g01397706 |
Show/hide table
Illustration 3 | g01397714 |
- Use Tooling (E) to install bushings (13) .
- Attach a suitable lifting device to centershift lock bar (8) .
Show/hide table
Illustration 4 | g01397600 |
- Position centershift lock bar (8) to the original location and install pin (10) .
- Attach a suitable lifting device to opposite side of centershift lock bar (8) .
Show/hide table
Illustration 5 | g01397593 |
- Position centershift lock bar (8) and install pin (9).
- Install lock (7) and bolts (6) .
- Attach a suitable lifting device to centershift cylinder (2) .
Show/hide table
Illustration 6 | g01397553 |
- Position centershift cylinder (2). Use the machine to position the cylinder rod.
- Install cap (4) and bolts (3) .
- Remove Tooling (A) and a suitable lifting device from blade lift arms (1) .
Show/hide table
Illustration 7 | g01397540 |
End By: Separate the steering frame lock.
Caterpillar Information System:
12M Motor Grader Machine Systems Centershift Lock Bar and Bushings - Remove
MH3049 Material Handler Hydraulic System Main Control Valve Air - Purge
559C, 579C, 2384C, and 2484C Knuckleboom Loaders TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565} 559C, 579C, 2384C, and 2484C Knuckleboom Loaders TA2 Technical Inspection{0372, 1000, 7000, 753T, 7565}
730C2 and 725C2 Articulated Truck Power Train Transmission Planetary - Assemble
349F and 352F Excavator Machine System Electrical Connector - Inspect
730C2 and 725C2 Articulated Truck Power Train Transmission Planetary - Disassemble
559C and 579C Knuckleboom Loaders Connector Locations
349F and 352F Excavators Determining Diagnostic Trouble Codes
990K Wheel Loader Alternate Exit
559C and 579C Knuckleboom Loaders General Information
2012/07/25 A New Alternator Harness Is Now Used on the AP500E Asphalt Paver {1406, 1408}
2012/08/07 New Bearing Group and Clevis Pin Is Now Used on AS4252C Screeds {5639, 5641}
12M Motor Grader Machine Systems Centershift Lock - Remove and Install
R1600H Load Haul Dump Power Train System Schematic
2012/08/08 A New Air Conditioner Relay is Now Available for Certain Load Haul Dump Machines {7320}
2012/08/08 A New Air Conditioner Relay is Now Available for Certain R1300G Load Haul Dump Machines {7320}
C27 and C32 Engines for Caterpillar Built Machines Piston and Rings
C27 and C32 Engines for Caterpillar Built Machines Exhaust Manifold
16M Series 3 and 18M Series 3 Motor Graders Fuel Tank Water and Sediment - Drain
3516B and 3516C Engines For MT4400D AC Off-Highway Trucks Data Link - Test
12M Motor Grader Machine Systems Centershift Lock - Disassemble
12M Motor Grader Machine Systems Centershift Lock - Assemble
12M Motor Grader Machine Systems Blade Lift Arm - Remove
12M Motor Grader Machine Systems Blade Lift Arm - Install