Boom Bearings and Seals - Remove and Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 350-7768 | Electric Hydraulic Pump Gp (115V) | 1 |
350-7769 | Electric Hydraulic Pump Gp (230V) | 1 | |
1M-6756 | Sleeve | 1 | |
1P-1839 | Bearing Puller Adapter | 1 | |
6V-3175 | Double Acting Cylinder | 1 | |
9U-6832 | Nut | 1 | |
165-3790 | Puller Stud | 1 |
Start By:
- Remove the boom.
- Remove lip seal (1).
Show/hide table
Illustration 2 g01705633 - Use Tooling (A) and a suitable lifting device to remove sleeve bearing (2) (not shown).
- Repeat Steps 1 through 2 to remove the lip seal and the sleeve bearing from the other side of the boom.
Show/hide table
Illustration 1 | g00479266 |
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
B | 350-7768 | Electric Hydraulic Pump Gp (115V) | 1 |
350-7769 | Electric Hydraulic Pump Gp (230V) | 1 | |
9U-5338 | Adapter | 1 | |
6V-3175 | Double Acting Cylinder | 1 | |
9U-6832 | Nut | 1 | |
165-3790 | Puller Stud | 1 | |
C | 1P-0520 | Driver Gp | 1 |
D | 452-6006 | Grease | 1 |
- Coat the sleeve bearing and the bearing bore with Tooling (D) prior to the installation of the sleeve bearing in the bore.
Note: Make sure that the sleeve bearings are installed in the bore so that the identification numbers of the sleeve bearings are facing outward.
Show/hide tableIllustration 3 g01705676 - Lower the temperature of sleeve bearing (2). Use Tooling (B) to install sleeve bearing (2) in the pin bore at the foot of the boom. Install sleeve bearing (2) until Dimension (W) is
9.5 ± 0.8 mm (0.37 ± 0.03 inch) .Show/hide tableIllustration 4 g01704933 - Use Tooling (C) to install lip seal (1) with the sealing lip toward the outside of the boom. Install lip seal (1) until lip seal (1) makes contact with sleeve bearing (2).
Note: Apply a thin layer of Tooling (D) to lip seal (1) prior to installation.
- Repeat Steps 1 through 3 to install the sleeve bearing and the lip seal on the other side of the boom.
Note: Make sure that the bores for the sleeve bearings are free of paint and of grease prior to the installation of the sleeve bearings.
End By:
- Install the boom.
Caterpillar Information System:
PM820, PM822, and PM825 Cold Planer Machine Systems Counterbalance Valve - Remove and Install - Steering Valve
986K Wheel Loader Hydraulic System Oil Filter (Hydraulic Fan Return) - Replace
CB2.5, CB2.7, CB2.9 and CC2.6 Vibratory Utility Compactors Propel System Case Drain Flow for Piston Motor (Wheel Propel) - Test
797F and 797F XQ Off-Highway Trucks Visual Service Procedure (VSP) Maintenance Intervals Seat Belt - Inspect
797F and 797F XQ Off-Highway Trucks Visual Service Procedure (VSP) Maintenance Intervals Rim - Inspect
Installation Procedure for Cat® Health Onboard System on Certain Cat Machines {7605, 7610, 7620} Installation Procedure for Cat® Health Onboard System on Certain Cat Machines {7605, 7610, 7620}
797F and 797F XQ Off-Highway Trucks Visual Service Procedure (VSP) Maintenance Intervals Differential and Final Drive Oil Filter - Replace
986K Wheel Loader Axle Oscillation Bearings - Lubricate
PM620 and PM622 Cold Planer Machine Systems Hydraulic Cylinder - Remove and Install - Guide Ski
D8T Track-Type Tractor Undercarriage - Clean
A New Clutch Piston Is Now Used on Certain 735C, 740C Ejector, and 745C Articulated Trucks {3030, 3160, 3170} A New Clutch Piston Is Now Used on Certain 735C, 740C Ejector, and 745C Articulated Trucks {3030, 3160, 3170}
Manufacturing Process for Stick Bushings Has Been Improved On Certain Backhoe Loaders {6502, 6533, 7551} Manufacturing Process for Stick Bushings Has Been Improved On Certain Backhoe Loaders {6502, 6533, 7551}
R1700 Load Haul Dump Power Train, Steering, Braking, Hydraulic, and Machine Systems Electronic Control (Hydraulic System)
3516E Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
Improved Database Procedure Is Now Available for Certain Cat® MineStar System {7605, 7610, 7620} Improved Database Procedure Is Now Available for Certain Cat® MineStar System {7605, 7610, 7620}
422F2, 426F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Leaving the Machine
3516E Engines for Caterpillar Built Machines Crankshaft Front Seal and Wear Sleeve - Remove and Install
New Stroke Limiter Collars Are Available for 16M, 16M3, 18M3, and 24M Motor Graders {5223} New Stroke Limiter Collars Are Available for 16M, 16M3, 18M3, and 24M Motor Graders {5223}
988K XE Wheel Loader Machine Systems Ride Control Accumulator - Disassemble
986K Wheel Loader Hydraulic Tank Breaker Relief Valve - Clean
988K XE Wheel Loader Machine Systems Ride Control Accumulator - Assemble
New Monitor Software is Now Used on Certain 415F2 and 427F2 Backhoe Loaders {108U, 1901, 7490, 7600, 7610, 7620} New Monitor Software is Now Used on Certain 415F2 and 427F2 Backhoe Loaders {108U, 1901, 7490, 7600, 7610, 7620}
986K Wheel Loader Hydraulic System Oil Level - Check
CCS9 Combination Vibratory Compactor Propel Systems Propel Control (Auto Vibe Control) - Calibrate