Crankshaft Front Seal and Wear Sleeve - Remove and Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 1U-7600 | Slide Hammer Puller | 1 |
| B | 484-7863 | Seal Installer | 1 |
Start By:
- Remove the vibration damper and the pulley.
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: If necessary, Use Tooling (A) to remove the crankshaft front seal and wear sleeve.
Show/hide table
| |
| Illustration 1 | g06114330 |
Note: Do not use any type of lubricant during the installation of the crankshaft front seal and the wear sleeve.
Note: Before installation of the crankshaft front seal and the wear sleeve, inspect the crankshaft for scratches. Also, inspect the crankshaft for any distortion on the surface that may lead to an out of round condition. Use a polishing cloth to remove any imperfections on the crankshaft.
Note: Clean the outside diameter of the crankshaft.
Show/hide table
| |
| Illustration 2 | g06114333 |
Show/hide table
| |
| Illustration 3 | g06114336 |
Show/hide table
| |
| Illustration 4 | g06114385 |
Show/hide table
| |
| Illustration 5 | g06114388 |
End By:
- Install the vibration damper and the pulley.
Caterpillar Information System:
422F2, 426F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Leaving the Machine
Improved Database Procedure Is Now Available for Certain Cat® MineStar System {7605, 7610, 7620} Improved Database Procedure Is Now Available for Certain Cat® MineStar System {7605, 7610, 7620}
3516E Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
R1700 Load Haul Dump Power Train, Steering, Braking, Hydraulic, and Machine Systems Electronic Control (Hydraulic System)
320D2 FM Forestry Machine Machine Systems Boom Bearings and Seals - Remove and Install
PM820, PM822, and PM825 Cold Planer Machine Systems Counterbalance Valve - Remove and Install - Steering Valve
986K Wheel Loader Hydraulic System Oil Filter (Hydraulic Fan Return) - Replace
CB2.5, CB2.7, CB2.9 and CC2.6 Vibratory Utility Compactors Propel System Case Drain Flow for Piston Motor (Wheel Propel) - Test
797F and 797F XQ Off-Highway Trucks Visual Service Procedure (VSP) Maintenance Intervals Seat Belt - Inspect
797F and 797F XQ Off-Highway Trucks Visual Service Procedure (VSP) Maintenance Intervals Rim - Inspect
Installation Procedure for Cat® Health Onboard System on Certain Cat Machines {7605, 7610, 7620} Installation Procedure for Cat® Health Onboard System on Certain Cat Machines {7605, 7610, 7620}
797F and 797F XQ Off-Highway Trucks Visual Service Procedure (VSP) Maintenance Intervals Differential and Final Drive Oil Filter - Replace
New Stroke Limiter Collars Are Available for 16M, 16M3, 18M3, and 24M Motor Graders {5223} New Stroke Limiter Collars Are Available for 16M, 16M3, 18M3, and 24M Motor Graders {5223}
988K XE Wheel Loader Machine Systems Ride Control Accumulator - Disassemble
986K Wheel Loader Hydraulic Tank Breaker Relief Valve - Clean
988K XE Wheel Loader Machine Systems Ride Control Accumulator - Assemble
New Monitor Software is Now Used on Certain 415F2 and 427F2 Backhoe Loaders {108U, 1901, 7490, 7600, 7610, 7620} New Monitor Software is Now Used on Certain 415F2 and 427F2 Backhoe Loaders {108U, 1901, 7490, 7600, 7610, 7620}
986K Wheel Loader Hydraulic System Oil Level - Check
CCS9 Combination Vibratory Compactor Propel Systems Propel Control (Auto Vibe Control) - Calibrate
D7E Track-Type Tractor Undercarriage - Clean
CCS9 Combination Vibratory Compactor Propel Systems Flushing Valve (Axle Propel Motor, Drum Propel Motor) - Test and Replace
CCS9 Combination Vibratory Compactor Propel Systems Machine Preparation for Troubleshooting
CCS9 Combination Vibratory Compactor Propel Systems Visual Inspection
CCS9 Combination Vibratory Compactor Propel Systems Propel System Troubleshooting