The Fuel Injector and Quill Installation Procedure is Being Updated for Certain C9.3B Engines {1251, 1290}
- Excavator
- 336 (S/N: SP91-UP; JHD1-UP; FEL1-UP; YBN1-UP; DKS1-UP; GDY1-UP)
- 340 (S/N: TYH1-UP)
- 345 GC (S/N: KEF1-UP)
- 340 (S/N: TYH1-UP)
- Industrial Engine
- C9.3B (S/N: NGH1-UP; NGL1-UP)
- Track Feller Buncher
- 521 (S/N: FKW1-UP)
- 522 (S/N: SJE1-UP; SJN1-UP)
- Track-Type Tractor
- D6 (S/N: GZ91-UP; LRG1-UP; D5M1-UP; HLY1-UP)
Introduction
The problem that is identified below has a known solution. Use the solution that is identified below.
Problem
The procedure for the Disassembly and Assembly needs to be updated to include the information below.
Solution
Show/hide table
Do not operate or work on this product unless you have read and understood the instruction and warnings in the relevant Operation and Maintenance Manuals and relevant service literature. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility. |
- Inspect the quill tubes and fuel injectors for cuts or marks at the mating surfaces.
- Replace any quill tubes since the quill tubes are a one time use component. Replace the copper washer when replacing the fuel injector.
- Follow the steps below for installing the quill tunes and fuel injectors.
- Seat the injector by installing and torquing the injector hold down clamp bolt to
30 ± 3 N·m (22 ± 2 lb ft) . - Install the quill tube and tighten the quill nut between
15 N·m (11 lb ft) to20 N·m (15 lb ft) . - Apply a final torque of
30 ± 3 N·m (22 ± 2 lb ft) to the injector hold down clamp bolt. - Apply a final torque between
50 N·m (37 lb ft) to55 N·m (41 lb ft) .
- Seat the injector by installing and torquing the injector hold down clamp bolt to
Caterpillar Information System:
308 Mini Hydraulic Excavators Boom and Stick Linkage - Lubricate - Offset Boom (If Equipped)
308 Mini Hydraulic Excavators Boom and Stick Linkage - Lubricate
Improved Dynamic Gas Blending (DGB) Regulator Service Kit is Now Available for Certain 3512C Engines {1270} Improved Dynamic Gas Blending (DGB) Regulator Service Kit is Now Available for Certain 3512C Engines {1270}
308 Mini Hydraulic Excavators Operator Controls
New Software Is Now Used for Certain C27 C32 Engines {1920} New Software Is Now Used for Certain C27 C32 Engines {1920}
313 and 313 GC Excavator Additional Messages
315 GC and 315 Excavator Diesel Exhaust Fluid Injector - Replace
313 and 313 GC Excavator Safety Messages
315 GC and 315 Excavator Fire Extinguisher Location
3516E Generator Sets Air Inlet Filter - Inspect/Clean/Test
315 GC and 315 Excavator Fuses - Replace
315 GC and 315 Excavator Engine Oil and Filter - Change
New Fuel Line Support Covers are Now Used for Certain C175 Off-Highway Truck Engines {1150, 795C} New Fuel Line Support Covers are Now Used for Certain C175 Off-Highway Truck Engines {1150, 795C}
New Fuel Injectors are Now Used on Certain C9 Engines {1251, 1290} New Fuel Injectors are Now Used on Certain C9 Engines {1251, 1290}
A New Oil Pan Site Glass Film is Now Used on Certain Off-Highway Truck Engines {7479} A New Oil Pan Site Glass Film is Now Used on Certain Off-Highway Truck Engines {7479}
A New Fan Blade Torque Procedure is Now Used on Certain 3516C 50 HZ Generator Sets {1356, 1359, 1360, 7174} A New Fan Blade Torque Procedure is Now Used on Certain 3516C 50 HZ Generator Sets {1356, 1359, 1360, 7174}
308 Mini Hydraulic Excavators Swing Gear and Bearing - Inspect
The Wiring Harness May Fail on Certain C13 Engines {1408, 1900} The Wiring Harness May Fail on Certain C13 Engines {1408, 1900}
The Dosing Cabinet Display for the Retrofit Aftertreatment is Discontinued {1408, 1900} The Dosing Cabinet Display for the Retrofit Aftertreatment is Discontinued {1408, 1900}
New Software is Now Used for Certain 3508 Engines {1920, 7620} New Software is Now Used for Certain 3508 Engines {1920, 7620}
Updated Flywheel Housing is Now Used on Certain C7 Powered Engines {1156, 1157} Updated Flywheel Housing is Now Used on Certain C7 Powered Engines {1156, 1157}
C7.1-XQ230 Rental Generator Set Coolant Sample (Level 1) - Obtain
C7.1-XQ230 Rental Generator Set Engine Air Cleaner Element - Replace
Improved Rear Cover Assemblies and Air Filter Supports Are Now Used for Certain 3500 60 Hz Generator Sets {726A} Improved Rear Cover Assemblies and Air Filter Supports Are Now Used for Certain 3500 60 Hz Generator Sets {726A}