New Integrated Sensor Module (ISM) Software Is Now Used for Certain G3600 Engines {1920, 1920}
- Engine
- G3606 (S/N: JFE1-950)
- G3608 (S/N: XH71-881)
- G3612 (S/N: BB21-769)
- G3616 (S/N: ZZY1-769)
- G3608 (S/N: XH71-881)
Description Of Change: The new ISM software has the following updates:
- High turbo shutdown level event applicable to G3616 A4 engines.
- ISM Electronic Technician (ET) configuration parameter for number of turbos has been set to maximum value of two turbos.
- Electronic Technician (ET) configuration parameter to set number of cylinders to address nuisance codes on cylinders that do not exist.
Adaptable To: The following changes are adaptable to the engines within the listed serial numbers, and are effective with all engines after the listed serial numbers.
The new and former part numbers are listed in Table 1.
Show/hide table
| Parts List | ||
| New Part Number | Part Name | Former Part Number(1) |
| Software Gp | ||
Show/hide table
| (1) | The former part number listed is for reference only and may differ. |
Note: The new software installation requires Cat® Electronic Technician (ET) 2017C.
Caterpillar Information System:
C7.1 Marine Propulsion Engine Sensors and Electrical Components
An Improved Camshaft Gear is Now Used on Certain C15 and C18 Machine Engines {1212} An Improved Camshaft Gear is Now Used on Certain C15 and C18 Machine Engines {1212}
C7.1 Marine Propulsion Engine Configuration Parameters
The Radiators May Leak Coolant Around the Gaskets on Certain XQC1600 Power Modules {1353} The Radiators May Leak Coolant Around the Gaskets on Certain XQC1600 Power Modules {1353}
336, 336 GC and 340 Excavator Systems Accumulator (Pilot) - Test and Charge - Pump Actuator
C7.1 Marine Propulsion Engine System Pressure Release
C7.1 Marine Propulsion Engine Belts - Inspect/Adjust/Replace
TA2 Technical Inspection for 3508B Generator Set Engines {0372, 1000, 7002, 753T, 7565} TA2 Technical Inspection for 3508B Generator Set Engines {0372, 1000, 7002, 753T, 7565}
C27 and C32 Generator Set Engines Fan Drive - Remove and Install - Lower Fan Drive
C27 and C32 Generator Set Engines Fan Drive - Remove and Install - Upper Fan Drive
PM820, PM822, and PM825 Cold Planer Machine Systems Control Valve - Remove and Install - Rear
307, 308, 309 and 310 EXCAVATOR Blade Lift Cylinder
New Turbo Water Supply Line Is Now Used on Certain Cat® Engines {1052, 1380} New Turbo Water Supply Line Is Now Used on Certain Cat® Engines {1052, 1380}
C7.1 Marine Propulsion Engine Engine Electronics
Improved Diesel Exhaust Fluid (DEF) Manifold Is Now Used on Certain Cat® Engines {108K, 3206} Improved Diesel Exhaust Fluid (DEF) Manifold Is Now Used on Certain Cat® Engines {108K, 3206}
Improved Diesel Exhaust Fluid (DEF) Manifold Is Now Used on Certain Cat® Products {108K, 3206} Improved Diesel Exhaust Fluid (DEF) Manifold Is Now Used on Certain Cat® Products {108K, 3206}
Power End Filtration Installation for Well Stimulation Pumps {5068, 6002} Power End Filtration Installation for Well Stimulation Pumps {5068, 6002}
AC Shore Power Harness Assembly is Now Labeled and Connected to Control Box on Certain C27 and C32 Generator Set Engines {1408} AC Shore Power Harness Assembly is Now Labeled and Connected to Control Box on Certain C27 and C32 Generator Set Engines {1408}
307, 308, 309 and 310 EXCAVATOR Fuel Lines
307, 308, 309 and 310 EXCAVATOR Hydraulic Tank and Filter
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Swing Motor
336 Excavator Machine Systems Camera - Remove and Install - Rear Camera
C27 and C32 Generator Set Engines Vibration Damper and Pulley - Remove and Install
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System Pilot Valve (Swing Parking Brake)