Fan Drive - Remove and Install - Upper Fan Drive
Start By:
- Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install".
- Remove the belt guard. Refer to Disassembly and Assembly, "Belt Guard - Remove and Install".
- Remove the belts. Refer to Operation and Maintenance Manual, "Belts - Inspect/Adjust/Replace".
Show/hide table
Illustration 1 g01289585 - Loosen bolts (1). Loosen locknut (2).
Show/hide table
Illustration 2 g01289589 - Attach a suitable lifting device onto fan drive (3). The weight of fan drive (3) is approximately
45 kg (100 lb) . Remove bolts (1). Remove fan drive (3).
- Attach a suitable lifting device onto fan drive (3). The weight of fan drive (3) is approximately
45 kg (100 lb) . Install fan drive (3). Install bolts (1).Show/hide table
Illustration 4 g01289585 - Install the belts. Refer to Operation and Maintenance Manual, "Belts - Inspect/Adjust/Replace".
- Tighten bolts (1). Tighten locknut (2).
Show/hide table
| |
| Illustration 3 | g01289589 |
End By:
- Install the belt guard. Refer to Disassembly and Assembly, "Belt Guard - Remove and Install".
- Install the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install".
Caterpillar Information System:
PM820, PM822, and PM825 Cold Planer Machine Systems Control Valve - Remove and Install - Rear
307, 308, 309 and 310 EXCAVATOR Blade Lift Cylinder
307, 308, 309 and 310 EXCAVATOR Air Cleaner
307, 308, 309 and 310 EXCAVATOR Air Conditioner Lines
336, 336 GC and 340 Excavator Systems Hydraulic System Air - Purge - Auxiliary Pump and PTO Drive
336, 336 GC and 340 Excavator Systems Hydraulic System Air - Purge - Fan Pump
336 Excavators (Powered by C9.3 Tier 4 Engine) Engine Supplement Clean Emissions Module - Remove and Install
3608 Engine Maintenance Interval Schedule
307, 308, 309 and 310 EXCAVATOR Air Cleaner
301.5, 301.6, 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavator Machine System General Information (Swing System)
336 Excavators (Powered by C9.3 Tier 4 Engine) Engine Supplement Turbocharger - Remove and Install
336, 336 GC and 340 Excavator Systems Pilot Lines
C27 and C32 Generator Set Engines Fan Drive - Remove and Install - Lower Fan Drive
TA2 Technical Inspection for 3508B Generator Set Engines {0372, 1000, 7002, 753T, 7565} TA2 Technical Inspection for 3508B Generator Set Engines {0372, 1000, 7002, 753T, 7565}
C7.1 Marine Propulsion Engine Belts - Inspect/Adjust/Replace
C7.1 Marine Propulsion Engine System Pressure Release
336, 336 GC and 340 Excavator Systems Accumulator (Pilot) - Test and Charge - Pump Actuator
The Radiators May Leak Coolant Around the Gaskets on Certain XQC1600 Power Modules {1353} The Radiators May Leak Coolant Around the Gaskets on Certain XQC1600 Power Modules {1353}
C7.1 Marine Propulsion Engine Configuration Parameters
An Improved Camshaft Gear is Now Used on Certain C15 and C18 Machine Engines {1212} An Improved Camshaft Gear is Now Used on Certain C15 and C18 Machine Engines {1212}
C7.1 Marine Propulsion Engine Sensors and Electrical Components
New Integrated Sensor Module (ISM) Software Is Now Used for Certain G3600 Engines {1920, 1920} New Integrated Sensor Module (ISM) Software Is Now Used for Certain G3600 Engines {1920, 1920}
New Turbo Water Supply Line Is Now Used on Certain Cat® Engines {1052, 1380} New Turbo Water Supply Line Is Now Used on Certain Cat® Engines {1052, 1380}
C7.1 Marine Propulsion Engine Engine Electronics