The Radiators May Leak Coolant Around the Gaskets on Certain XQC1600 Power Modules {1353}
- Power Module
- XQC1600 (S/N: N1M1-UP)
Introduction
The problem that is identified below does not have a known permanent solution. Until a permanent solution is known, use the solution that is identified below.
Problem
The 452-9595 Radiator Gp is experiencing coolant leakage around the radiator gaskets on XQC1600 power modules.
Solution
Show/hide table
Do not operate or work on this product unless you have read and understood the instruction and warnings in the relevant Operation and Maintenance Manuals and relevant service literature. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility. |
Show/hide table
Illustration 1 | g06291636 |
(1) Center brace |
- Remove center braces (1) to access fastening hardware.
Show/hide table
Illustration 2 g06291646 Show/hide tableIllustration 3 g06291650 - Tighten all radiator M8 nuts on the radiator to
41 ± 7 N·m (30 ± 5 lb ft) using the sequence shown in Illustration 2 (start at center and work outwards). Use a back-up wrench. Tighten nuts while radiator core is in a vertical position.Note: It is only required to tighten M8 nuts where gaskets are used in the joint.
Caterpillar Information System:
336, 336 GC and 340 Excavator Systems Accumulator (Pilot) - Test and Charge - Pump Actuator
C7.1 Marine Propulsion Engine System Pressure Release
C7.1 Marine Propulsion Engine Belts - Inspect/Adjust/Replace
TA2 Technical Inspection for 3508B Generator Set Engines {0372, 1000, 7002, 753T, 7565} TA2 Technical Inspection for 3508B Generator Set Engines {0372, 1000, 7002, 753T, 7565}
C27 and C32 Generator Set Engines Fan Drive - Remove and Install - Lower Fan Drive
C27 and C32 Generator Set Engines Fan Drive - Remove and Install - Upper Fan Drive
PM820, PM822, and PM825 Cold Planer Machine Systems Control Valve - Remove and Install - Rear
307, 308, 309 and 310 EXCAVATOR Blade Lift Cylinder
307, 308, 309 and 310 EXCAVATOR Air Cleaner
307, 308, 309 and 310 EXCAVATOR Air Conditioner Lines
336, 336 GC and 340 Excavator Systems Hydraulic System Air - Purge - Auxiliary Pump and PTO Drive
336, 336 GC and 340 Excavator Systems Hydraulic System Air - Purge - Fan Pump
C7.1 Marine Propulsion Engine Configuration Parameters
An Improved Camshaft Gear is Now Used on Certain C15 and C18 Machine Engines {1212} An Improved Camshaft Gear is Now Used on Certain C15 and C18 Machine Engines {1212}
C7.1 Marine Propulsion Engine Sensors and Electrical Components
New Integrated Sensor Module (ISM) Software Is Now Used for Certain G3600 Engines {1920, 1920} New Integrated Sensor Module (ISM) Software Is Now Used for Certain G3600 Engines {1920, 1920}
New Turbo Water Supply Line Is Now Used on Certain Cat® Engines {1052, 1380} New Turbo Water Supply Line Is Now Used on Certain Cat® Engines {1052, 1380}
C7.1 Marine Propulsion Engine Engine Electronics
Improved Diesel Exhaust Fluid (DEF) Manifold Is Now Used on Certain Cat® Engines {108K, 3206} Improved Diesel Exhaust Fluid (DEF) Manifold Is Now Used on Certain Cat® Engines {108K, 3206}
Improved Diesel Exhaust Fluid (DEF) Manifold Is Now Used on Certain Cat® Products {108K, 3206} Improved Diesel Exhaust Fluid (DEF) Manifold Is Now Used on Certain Cat® Products {108K, 3206}
Power End Filtration Installation for Well Stimulation Pumps {5068, 6002} Power End Filtration Installation for Well Stimulation Pumps {5068, 6002}
AC Shore Power Harness Assembly is Now Labeled and Connected to Control Box on Certain C27 and C32 Generator Set Engines {1408} AC Shore Power Harness Assembly is Now Labeled and Connected to Control Box on Certain C27 and C32 Generator Set Engines {1408}
307, 308, 309 and 310 EXCAVATOR Fuel Lines
307, 308, 309 and 310 EXCAVATOR Hydraulic Tank and Filter