Engine Oil Pan - Remove and Install
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Drain the engine oil into a suitable container for storage or for disposal.
Show/hide table
Illustration 1 g01123595 - Remove bolts (1) that hold the connector for the oil pump to engine oil pan (2).
Show/hide table
Illustration 2 g01123597 - Remove bolts (3) that connect engine oil pan (2) to the cylinder block.
Show/hide table
Improper lift rigging can allow unit to tumble causing injury and damage.
Show/hide tableIllustration 3 g01123599 - Attach a suitable lifting device to the engine lifting eyes. The weight of the 3512C Engine is approximately
5900 kg (13,000 lb) . The weight of the oil pan is approximately295 kg (650 lb) . - Lift the engine from the oil pan.
Show/hide table
Illustration 4 g01123600 - Remove oil pan gasket (4) from the engine oil pan. Remove O-ring seal (5). Remove bolts (6). Remove flange (7) from the engine oil pan. Remove seal (8) from the flange.
- Install engine oil pan (2) in the reverse order of removal.
Caterpillar Information System:
CX31 and CX31 HT On-Highway Transmissions (Cat Truck) Relief Valve (Torque Converter Inlet) Pressure - Test
CX31 and CX31 HT On-Highway Transmissions (Cat Truck) Relief Valve (Transmission Hydraulic Control) - Test and Adjust
3512C Engine Engine Oil Filter Housing - Remove and Install
3512C Engine Engine Oil Pump - Remove and Install
326F and 330F Excavator Machine Systems Relief Valve (Pilot)
WS063, WSF063 and WSP063 Well Stimulation Pumps Seal (Crosshead Rod) - Remove and Install
C8.7 Marine Engine Coolant Level - Check
3512C Engine Engine Oil Cooler - Remove and Install
3512C Engine Water Pump - Remove and Install
WS063, WSF063 and WSP063 Well Stimulation Pumps Flange (Discharge) - Remove and Install
CX31 and CX31 HT On-Highway Transmissions (Cat Truck) Power Train Pressures
CX31 and CX31 HT On-Highway Transmissions (Cat Truck) Hydraulic Oil Contamination - Test
C175-16 Petroleum Engines Engine Oil Pressure - Test
CX31 and CX31 HT On-Highway Transmissions (Cat Truck) Oil Filter (Transmission)
WS063, WSF063 and WSP063 Well Stimulation Pumps Gearbox (Input Drive) - Remove and Install
C8.7 and C12.9 Marine Engines Valve Lash Is Excessive
3512C Engine Engine Oil Pan - Disassemble
Differences in Appearance of Cat ® Reman Parts when Compared to New Parts {1000, 1250} Differences in Appearance of Cat ® Reman Parts when Compared to New Parts {1000, 1250}
C8.7 and C12.9 Marine Engines Cylinder Is Noisy
C4.4 Marine Generator Set Magnetic Pickup
C4.4 Marine Generator Set Engine Oil Pan Drain Valve
C175-16 Petroleum Engines Air Shutoff
C8.7 and C12.9 Marine Engines Electronic Service Tool Does Not Communicate
WS063, WSF063 and WSP063 Well Stimulation Pumps Crosshead - Remove and Install