- Wheel Loader:
- 950M (S/N: EMB1-UP; XCJ1-UP; FTR1-UP; J1S1-UP)
- 962M (S/N: EJB1-UP; JYD1-UP; J2S1-UP; F2T1-UP)
Introduction
This Special Instruction will provide information on installation of 484-6930 Kit Upper Guard .
Do not perform any procedure in this publication or order any parts until you understand the information that is contained in this publication.
Safety Section
 |
Improper operation, lubrication, maintenance or repair of this product can be dangerous and could result in injury or death. Do not operate or perform any lubrication, maintenance or repair on this product, until you have read and understood the operation, lubrication, maintenance and repair information. |
 |
|
Personal injury can result from flame cutting or welding on painted areas. The effect of gasses from burned paint is a hazard to the person doing the cutting or welding. Do not flame cut or weld on painted areas. |
|
|
Personal injury or death can result from fumes, gases and ultraviolet rays from the weld arc. Welding can cause fumes, burn skin and produce ultraviolet rays. Keep your head out of the fumes. Use ventilation, exhaust at the arc, or both, to keep fumes and gases from your breathing area. Wear eye, ear and body protection before working. Protect yourself and others; read and understand this warning. Fumes and gases can be dangerous to your health. Ultraviolet rays from the weld arc can injure eyes and burn skin. Electric shock can cause death. Read and understand the manufacturer's instructions and your employer's safety practices. Do not touch live electrical parts. See "American National Standard Z49.1, Safety in Welding and Cutting" published by the American Welding Society. American Welding Society2501 N.W. 7th Street Miami, Florida 33125 See "OSHA Safety and Health Standards, 29 CFR 1910", available from U.S. Department of Labor. U.S. Department of LaborWashington, D.C. 20210 |
|
|
Use an appropriate lifting device that is rated for the specific load. Failure to do so can result in serious injury or death. |
|
| NOTICE |
|---|
Before carrying out arc welding on the machine or on any equipment attached to the machine, disconnect all power and ground leads from the batteries in order to avoid possible damage to electronic components. |
Note: Use proper lifting device as necessary to support components during installation.
Required Parts
| 484-6930 Kit Upper Guard | |||
|---|---|---|---|
| Item | Qty | Part Number |
Description |
| 1 | 7 | 8T-4967 | Weld Stud |
| 2 | 8 | 446-5835 | Weld Stud |
| 3 | 1 | 395-2954 | Guard-RH |
| 4 | 1 | 395-2956 | Guard-LH |
| 5 | 1 | 416-7096 | Guard As |
| 6 | 1 | 416-7098 | Guard-LH |
| 7 | 25 | 7X-7729 | Washer |
| 8 | 15 | 8T-4133 | Nut |
| 9 | 8 | 8T-4136 | Bolt |
| 10 | 2 | 8T-4137 | Bolt |
| 11 | 1 | 372-4665 | Cover-RH |
| 12 | 1 | 372-4667 | Cover-LH |
| 13 | 8 | 7X-0618 | Hard Washer |
| 14 | 8 | 8T-4244 | Nut |
Welding
Engine End Frame (EEF)
- Weld seven studs (1) to the EEF as per dimensions shown in Illustration 1.
 | |
| Illustration 1 | g03883087 |
EEF Front side view (1) 8T-4967 Weld Stud (A) 481.1 ± 1.5 mm (18.94 ± 0.06 inch) (B) 343.1 ± 1.5 mm (13.51 ± 0.06 inch) (C) 113.1 ± 1.5 mm (4.45 ± 0.06 inch) (D) 326.6 ± 1.5 mm (12.86 ± 0.06 inch) (E) 648.1 ± 1.5 mm (25.52 ± 0.06 inch) (F) 164.5 ± 1.5 mm (6.48 ± 0.06 inch) (G) 164.5 ± 1.5 mm (6.48 ± 0.06 inch) (H) 90 ± 1.5 mm (3.54330 ± 0.06 inch) (J) 122 ± 1.5 mm (4.80314 ± 0.06 inch) (K) 170 ± 1.5 mm (6.69290 ± 0.06 inch) (W1) All around fillet weld | |
 | |
| Illustration 2 | g03884890 |
EEF Left side view (2) 446-5835 Weld Stud (L) 779.7 mm (30.7 inch) (M) 29 mm (1.14 inch) (N) 713.8 mm (28.1 inch) (P) 1198.1 mm (47.17 inch) (R) 810.3 mm (31.91 inch) (S) 810.2 mm (31.9 inch) (T) 1197 mm (47.13 inch) (W2) All around fillet weld | |
- Weld four studs (2) to the Left side of EEF as per dimensions shown in Illustration 2.
 | |
| Illustration 3 | g03884166 |
EEF Right side view (2) 446-5835 Weld Stud (L) 779.7 mm (30.7 inch) (M) 29 mm (1.14 inch) (N) 713.8 mm (28.1 inch) (P) 1198.1 mm (47.17 inch) (R) 810.3 mm (31.91 inch) (S) 810.2 mm (31.9 inch) (T) 1197 mm (47.13 inch) (W2) All around fillet weld | |
- Weld four studs (2) to the Right side of EEF as per dimensions shown in Illustration 3.
Guard Assembly Location
Note: Use proper lifting device as necessary to support components during installation.
 | |
| Illustration 4 | g03886614 |
Guard Installation on Engine End Frame
Note: Use proper lifting device as necessary to support components during installation.
- Install Guard-RH (3), Guard-LH (4), Guard As (5), and Guard-LH (6) on the frame. Secure guards to the fabricated studs using eight bolts (9), two bolts (10), twenty-five washers (7), and fifteen nuts (8).
Note: Use proper lifting device as necessary to support components during installation.
 | |
| Illustration 5 | g03883094 |
View of area A (3) 395-2954 Guard-RH (4) 395-2956 Guard-LH (5) 416-4096 Guard As (6) 416-7098 Guard-LH (7) 7X-7729 Washer (8) 8T-4133 Nut (9) 8T-4136 Bolt (10) 8T-4137 Bolt | |
Cover Location - Right Side
 | |
| Illustration 6 | g03883096 |
Cover Installation on EEF - Right Side
Note: Use proper lifting device as necessary to support components during installation.
- Install cover (11) using four hard washers (13) and four nuts (14) .
 | |
| Illustration 7 | g03883493 |
View of area B (11) 372-4665 Cover-RH (13) 7X-0618 Hard Washer (14) 8T-4244 Nut | |
Cover Location - Left Side
 | |
| Illustration 8 | g03886677 |
Cover Installation on EEF - Left Side
Note: Use proper lifting device as necessary to support components during installation.
