Overspeed Verification of the Marine Power Display (MPD){7410, 7427, 7490}
- Engine:
- 3508B (S/N: S2A1-UP; S2B1-UP; S2D1-UP; S2E1-UP; S2F1-UP)
- 3512B (S/N: MKH1-UP; S2G1-UP; S2H1-UP; S2J1-UP; S2K1-UP; S2L1-UP; S2M1-UP; S2N1-UP)
- 3516B (S/N: PAG1-UP; S2P1-UP; S2R1-UP; S2S1-UP; S2T1-UP; S2W1-UP; S2X1-UP; S2Y1-UP)
- 3512B (S/N: MKH1-UP; S2G1-UP; S2H1-UP; S2J1-UP; S2K1-UP; S2L1-UP; S2M1-UP; S2N1-UP)
The following procedure for Overspeed verification in the MPD applies to the following engines:
- Marine Auxiliary
- Marine Propulsion
The panel for the MPD verifies the functionality for the overspeed for both the primary ECM and secondary ECM simultaneously. No additional procedure is needed to perform verification for the secondary ECM (Propulsion Engine).
Refer to Step 1 through Step 4 in order to test the overspeed verification.
- Scroll through the screens of information that are displayed on the MPD. Depress the "Menu" button (1) in order to display the "Engine Configuration" screen. Refer to Illustration 1.
Show/hide table
Illustration 1 | g01298215 |
Screens of Information (1) "Menu" button |
- Depress the Down Arrow button (2) in order to select the "Overspeed Verify". Refer to Illustration 2.
Show/hide table
Illustration 2 | g01298218 |
"Engine Configuration" Screen (2) Down Arrow Button |
- Depress the "Change Torque Limit" button (3) in order to select the ON position for the "Overspeed Verify".
Show/hide table
Illustration 3 | g01298221 |
"Engine Configuration" Screen (3) "Change Torque Limit" Button |
- Run the engine at 75 percent of the value that is programmed for overspeed.
An overspeed event will activate. An entry for the event will be logged. The engine will shut down. With the shutting down of the engine, the procedure to verify overspeed is completed.
- Cycle power to the engine in order to bring the engine back to a normal stage. The Overspeed verification will not be active.
Caterpillar Information System:
Corrective Action for Speed/Timing Sensor{1901, 1912} Corrective Action for Speed/Timing Sensor{1901, 1912}
C15 On-Highway Engine Crankcase Pressure Sensor - Remove and Install
G3520C and G3520E Generator Set Engines Oil Pressure Is Low
C7 and C9 On-Highway Engines General Information
C13 and C15 On-highway Engines Driver Questionnaire Response
C13 and C15 On-highway Engines Symptom Troubleshooting
C7 and C9 On-Highway Engines Exhaust Has Black Smoke
C13 and C15 On-highway Engines Welding Precaution
C7 and C9 On-Highway Engines Acceleration Is Poor or Throttle Response Is Poor
14L Motor Grader Power Train Solenoid Valve (Parking Brake)
C280-12 and C280–16 Marine Engines Camshaft Drive Gear - Install
C13 and C15 On-highway Engines Vehicle Speed - Calibrate
C7 and C9 On-Highway Engines Retarder Does Not Activate
3176C and 3196 Engines for Caterpillar Built Machines Fuel Priming Pump
TA22-4WD Agricultural Transmission Transmission Suction Screen - Clean
C13 and C15 On-highway Engines Auxiliary Brake - Test
C13 and C15 On-highway Engines Indicator Lamp - Test
TA22 Transmission Relief Valve - Remove and Install - Lube Relief Valve
Using the Map Adjustment Feature{1901, 1902, 7620} Using the Map Adjustment Feature{1901, 1902, 7620}
307B, 311–330 B-D Series, 345–5090 B and C Series and M312-M322 A-D Series Excavators Bucket - Remove and Install
C280-12 and C280–16 Marine Engines Idler Gears (Rear) - Remove
12M Motor Grader Scarifier Lift Link Socket - Lubricate - If Equipped
C280-12 and C280–16 Marine Engines Idler Gears (Rear) - Install
12M Motor Grader Scarifier Teeth - Inspect/Replace - If Equipped