Idler Gears (Rear) - Install
安装步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 138-7573 | 连杆支架 | 1 |
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 如果轴承已从齿轮 (4) 上拆下，将轴承安装到齿轮。 轴承应处于齿轮水平下方3.0 ± 0.5 mm (0.12 ± 0.02 in)。 安装后轴承内径应为 150.002 ± 0.020 mm (5.9056 ± 0.0008 in)。
Show/hide table
 | |
| 图 1 | g01296176 |
- 将齿轮 (4) 和挡圈 (5) 在轴 (11) 上放好。 安装螺栓 (6) 和工具 (A) 。
- 用工具 (A) 和一个合适的举升设备来安装轴 (11) 和齿轮 (4) 。 轴 (11) 和齿轮 (4) 的重量约为 41 kg (90 lb)。 将轴 (11) 和齿轮 (4) 在缸体上放好。 安装螺栓 (12) 。 请参阅技术规范, "齿轮组件（后部）"，了解正确的扭矩
- 拆下工具 (A) ，并安装剩余螺栓 (6) 。
- 为其它惰轮重复步骤2和步骤4。
- 将轴 (9) 在缸体上放好。 安装螺栓 (10) 。 请参阅技术规范, "齿轮组件（后部）"，了解正确的扭矩
- 如果轴承已从齿轮 (8) 上拆下，将轴承安装到齿轮中。 轴承应处于具有更小肩部的齿轮侧表面下方3.0 ± 0.5 mm (0.12 ± 0.02 in)。
- 将齿轮 (1) 在齿轮 (8) 上放好。 安装螺栓 (7) 。
- 将合适的起吊设备连接到齿轮 (1) 。 齿轮 (1) 和齿轮 (8) 的重量约为 55 kg (121 lb)。 将齿轮 (1) 和齿轮 (8) 安装在轴 (9) 上。 对齐齿轮 (1) 上的齿和曲轴齿轮上的齿。
- 安装挡圈 (2) 和螺栓 (3) 。
End By: 安装后壳体。 请参阅 拆解和组装, "壳体（后）- 安装"。
Caterpillar Information System:
12M Motor Grader Scarifier Lift Link Socket - Lubricate - If Equipped
C280-12 and C280–16 Marine Engines Idler Gears (Rear) - Remove
307B, 311–330 B-D Series, 345–5090 B and C Series and M312-M322 A-D Series Excavators Bucket - Remove and Install
Using the Map Adjustment Feature{1901, 1902, 7620} Using the Map Adjustment Feature{1901, 1902, 7620}
TA22 Transmission Relief Valve - Remove and Install - Lube Relief Valve
C13 and C15 On-highway Engines Indicator Lamp - Test
C13 and C15 On-highway Engines Auxiliary Brake - Test
TA22-4WD Agricultural Transmission Transmission Suction Screen - Clean
3176C and 3196 Engines for Caterpillar Built Machines Fuel Priming Pump
C7 and C9 On-Highway Engines Retarder Does Not Activate
Overspeed Verification of the Marine Power Display (MPD){7410, 7427, 7490} Overspeed Verification of the Marine Power Display (MPD){7410, 7427, 7490}
Corrective Action for Speed/Timing Sensor{1901, 1912} Corrective Action for Speed/Timing Sensor{1901, 1912}
12M Motor Grader Scarifier Teeth - Inspect/Replace - If Equipped
2006/09/01 277-4734 Bypass Harness Assembly Allows Cat Electronic Technician (Cat ET) to Communicate with ADEM IV:E2 Electronic Control Modules {0779, 0785, 1901, 1930}
C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Injection Lines
C1.5 and C2.2 Engines for Caterpillar Built Machines Turbocharger
C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Lines
C7 Engines for Caterpillar Built Machines Water Temperature Regulator
C7 Engines for Caterpillar Built Machines Water Temperature Regulator
12M Motor Grader Work Tool Lift - Lubricate
320D and 323D Excavators Machine System Specifications Pilot Valve (Joystick)
C7 Engines for Caterpillar Built Machines Crankshaft
C15 and C18 Petrolem Generator Set Engines ECM Software - Install
C1.5 and C2.2 Engines for Caterpillar Built Machines Fan Drive