Camshaft Drive Gear - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 6V-6080     | 扭矩倍增器     | 1     |
5P-1748 | 套筒     | 1     | |
B     | 4C-5593     | 防粘结剂     | -     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将凸轮轴正时销 (8) 安装在凸轮轴中。
Show/hide table
图 1 | g01294950 |
注: 如果正时销无法安装在凸轮轴上,可能需要松开摇臂调整螺钉和喷油器调整螺钉。 这样做可以转动凸轮轴。
- 将正时销钉安装到曲轴内。
- 将板 (7) 在凸轮轴驱动齿轮 (3) 上放好。 安装螺栓 (4) 。
Show/hide table
图 2 | g01294949 |
Show/hide table
图 3 | g01294966 |
Show/hide table
图 4 | g01294805 |
- 在螺栓 (6) 的螺纹上涂抹工具 (B) 。
- 将适当的起吊设备连接在凸轮轴驱动齿轮 (3) 上。 凸轮轴驱动齿轮 (3) 的重量约为 35 kg (77 lb)。 将凸轮轴驱动齿轮 (3) 在凸轮轴上放好。 安装垫圈 (5) 和螺栓 (6) 。 用手拧紧螺栓 (6) 。
注: 凸轮轴驱动齿轮 (3) 在边上带有标记 (S) 和 (R) 。 如果发动机正常转动,标记 (S) 朝向主速度传感器。 如果发动机反向转动,标记 (R) 朝向主速度传感器。
- 将转速正时轮 (1) 在凸轮轴驱动齿轮 (3) 上放好。 安装螺栓 (2) 并使螺栓处于松动状态。 确保转速正时轮 (1) 处于正确位置并拧紧螺栓 (2) 。
注: 转速正时轮 (1) 上附加齿后的第一个齿应与主速度传感器对齐。
- 将曲轴正时销从曲轴上拆下。
- 向后转动飞轮大约20度。
Show/hide table
注意 |
---|
如果只拆下了一个凸轮轴驱动齿轮,则在转动发动机前必须从未拆下驱动齿轮的凸轮轴上拆卸凸轮轴正时销。 |
- 沿正常发动机旋向转动飞轮,直到曲轴正时销可以重新装入曲轴。 本步骤将正时齿轮的齿隙保持在正常发动机旋向。
Show/hide table
注意 |
---|
如果转动凸轮轴超过20度,活塞和气门之间可能存在干扰。 |
- 如果错过曲轴正时销的位置,不要沿着同一方向继续转动飞轮。 如果错过曲轴正时销的位置,请重复步骤8和步骤9。
- 拆下凸轮轴正时销和曲轴正时销。
- 使用工具 (A) 拧紧螺母 (6) ,使其扭矩达到 2000 ± 275 N·m (1480 ± 200 lb ft)。
- 用冲头和锤子敲击板 (7) 。 冲头必须由黄铜或青铜制成。 这将使齿轮落座在锥形驱动轴上。 重复进行步骤12。 重复此步骤直到扭矩不再变化。
- 识别正确的凸轮轴正时。 请参考测试和调整, "凸轮轴正时"。
- 拆下曲轴正时销钉和凸轮轴正时销钉。 将正时销装回正确的保存位置。
- 将后凸轮轴检查盖安装在发动机两侧。
Caterpillar Information System:
C13 and C15 On-highway Engines Vehicle Speed - Calibrate
C175-16 Locomotive Engine General Information (Air/Electric Starting System)
2006/10/02 New 271-8590 Analyzer Gp (24-Volt) Quickly Identifies Starting and Charging System Problems {0709, 1406}
C7 Engines for Caterpillar Built Machines Turbocharger
C-10 and C-12 Truck Engines Cylinder Liner
C13, C15, and C18 Tier 4 Final Engines Fuel Filter Base
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Firmware - Update
C280-12 and C280–16 Marine Engines Camshaft Drive Gear - Remove
C7 Engines for Caterpillar Built Machines Valve Mechanism Cover
TA22-4WD Agricultural Transmission Lubricant Viscosities
C7 Engines for Caterpillar Built Machines Valve Mechanism Cover
C175-16 and C175-20 Engines for Off-Highway Trucks Ether Control System
14L Motor Grader Power Train Solenoid Valve (Parking Brake)
C7 and C9 On-Highway Engines Acceleration Is Poor or Throttle Response Is Poor
C13 and C15 On-highway Engines Welding Precaution
C7 and C9 On-Highway Engines Exhaust Has Black Smoke
C13 and C15 On-highway Engines Symptom Troubleshooting
C13 and C15 On-highway Engines Driver Questionnaire Response
C7 and C9 On-Highway Engines General Information
G3520C and G3520E Generator Set Engines Oil Pressure Is Low
C15 On-Highway Engine Crankcase Pressure Sensor - Remove and Install
Corrective Action for Speed/Timing Sensor{1901, 1912} Corrective Action for Speed/Timing Sensor{1901, 1912}
Overspeed Verification of the Marine Power Display (MPD){7410, 7427, 7490} Overspeed Verification of the Marine Power Display (MPD){7410, 7427, 7490}
C7 and C9 On-Highway Engines Retarder Does Not Activate