Steering Differential and Brake - Disassemble
拆解步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 说明     | 数量     |
A     | 138-7573     | 连杆支架     | 2     |
B     | 3K-4897     | 弹簧销     | 8     |
C     | 6V-4072     | 活动扳手     | 1     |
D     | 9S-9154     | 踏脚板     | 1     |
6V-3009 | Bar     | 1     | |
8S-6470 | 顶出螺钉 3/4 in - 16 x 4 in     | 1     | |
8S-5133 | 螺塞     | 1     | |
5P-8245 | 垫圈     | 4     | |
1D-4719 | 螺母 1/2 in - 13     | 2     | |
2H-6488 | 螺栓 1/2 in - 13 x 5 in     | 2     | |
E     | 9S-9154     | 踏脚板     | 1     |
6V-3009 | Bar     | 1     | |
8S-6470 | 顶出螺钉 3/4 in - 16 x 4 in     | 1     | |
8S-5133 | 螺塞     | 1     | |
5P-8245 | 垫圈     | 4     | |
1D-4719 | 螺母 1/2 in - 13     | 2     | |
1D-4574 | 螺栓 1/2 in - 13 x 6 in     | 2     | |
8H-0663 | 轴承拉拔器     | 1     | |
F     | 138-7575     | 连杆支架     | 3     |
G     | 8B-7550     | 腿     | 2     |
8B-7559 | 接头     | 2     | |
3H-0465 | 板     | 4     | |
1P-0498 | 板     | 1     | |
1B-4207 | 螺母 3/4 in - 16     | 2     | |
5H-9976 | 顶出螺钉 1 in - 14 x 5 3/4 in     | 1     | |
5B-0637 | 螺母 1 in - 14     | 1     | |
8H-0684 | 棘轮扳手     | 1     | |
8B-7563 | 手柄     | 1     | |
5F-7353 | 垫圈 (止推)     | 1     | |
8B-7548 | 推拉器工具总成     | 1     |
开始:
- 拆下左侧终传动、转向差速器和制动器。 请参阅拆解和组装, "终传动、转向差速器和制动器(左侧)- 拆卸"。
- 卸下螺栓 (1) 和垫圈。
Show/hide table
图 1 | g00823680 |
- 拆下两个相对的螺栓 (2) 。
- 安装工具 (A) 和适当的起吊设备。
Show/hide table
图 2 | g00823691 |
- 拆下滑动托架 (3) 。 滑动托架 (3) 的重量约为 48 kg (105 lb)。
- 拆下工具 (A) 。
- 从行星齿轮架 (7) 上卸下其余的螺栓 (2) 和挡油环 (4) 。
Show/hide table
图 3 | g00823756 |
- 从齿圈 (6) 拆下挡圈 (5) 、止推环和行星齿轮架 (7) 。
- 从行星齿轮架 (7) 上拆下密封圈 (10) 。
Show/hide table
图 4 | g00823775 |
- 用锤子和冲头将销 (12) 冲入轴 (11) 中。
- 从行星齿轮架 (7) 上拆下轴 (11) 、行星齿轮 (9) 、盘 (8) 和轴承 (13) 。
- 从轴 (11) 上卸下销 (12) 。
- 对其余的行星齿轮重复步骤 9 至 11。
- 拆下锁环 (14) 后拆下挡圈 (16) 。
Show/hide table
图 5 | g00823759 |
- 从行星齿轮架 (18) 拆下太阳齿轮 (15) 。
- 拆下间隔套 (17) 。
- 从行星齿轮架 (18) 拆下螺栓 (19) 、板 (20) 和齿轮 (21) 。
Show/hide table
图 6 | g00823816 |
- 使用工具 (B) 压缩将行星齿轮架 (18) 固定在齿圈 (6) 中的挡圈。
- 将 行星齿轮 架 (18) 与齿圈 (6) 分离。
- 从行星齿轮架 (18) 拆卸挡圈。
- 用锤子和冲头将销 (23) 冲入轴 (24) 中。
- 从行星齿轮架 (18) 上拆下轴 (24) 、行星齿轮 (22) 、盘 (26) 和轴承 (25) 。
Show/hide table
图 7 | g00823872 |
- 从轴 (24) 上卸下销 (23) 。
- 对其余的行星齿轮重复步骤 20 至 22。
- 将螺栓置于小伞齿轮 (27) 的轮齿中,以防止移动。
Show/hide table
图 8 | g00823878 |
- 将锁紧垫圈 (29) 上的舌片朝远离螺母 (28) 的方向弯折。
Show/hide table
图 9 | g00823884 |
- 使用工具 (C) 从小伞齿轮拆下螺母 (28) 。
- 从小伞齿轮拆下锁紧垫圈 (29) 和垫圈 (30) 。
- 拆下螺栓 (32) 。
- 从支架上拆下行星齿轮架 (31) 。
- 使用工具 (D) 从轴承内圈 (33) 和行星齿轮架 (31) 推动小伞齿轮 (27) 。
Show/hide table
图 10 | g00823890 |
- 使用工具 (E) 从小伞齿轮 (27) 拆卸轴承内圈 (34) 。
Show/hide table
图 11 | g00824243 |
- 从行星齿轮架 (31) 上拆下轴承杯 (35) 。
Show/hide table
图 12 | g00824263 |
- 拆下螺栓 (36) 。
Show/hide table
图 13 | g00824265 |
- 将支架 (37) 和垫片 (38) 从壳体上拆下。
- 拆下螺栓 (39) 。
- 将伞齿轮 (40) 从壳体 (41) 上拆下。
- 将工具 (F) 和适当的起吊设备连接到制动器壳体 (42) 上。
Show/hide table
图 14 | g00824268 |
- 拆下螺栓 (43) 。
- 将制动器壳体 (42) 从终传动壳体 (44) 上拆下。 制动壳体 (42) 的重量约为 150 kg (335 lb)。
- 拆下螺栓和垫圈 (45) 。
Show/hide table
图 15 | g00824819 |
Show/hide table
图 16 | g00824349 |
Show/hide table
弹簧加压的零件和/或盖板可能导致人身伤害。 拆卸盖板时弹簧力将被释放。 松动螺栓时做好准备把持住弹簧加载的盖板。 |
- 拆下护圈 (46) 和止推垫圈 (47) 。
- 拆卸毂 (48) 、摩擦片和制动器板 (49) 。
- 必要时,将环 (50) 从毂 (48) 上拆下。
- 拆下止推垫圈 (51) 。
- 缓慢地拆卸螺栓 (52) 。
Show/hide table
图 17 | g00824351 |
Show/hide table
弹簧加压的零件和/或盖板可能导致人身伤害。 拆卸盖板时弹簧力将被释放。 松动螺栓时做好准备把持住弹簧加载的盖板。 |
- 从制动器壳体 (42) 拆卸护圈 (53) 、环 (54) 和密封圈 (55) 。
- 从制动器壳体 (42) 拆卸螺栓 (56) 、板 (57) 、垫片组 (58) 、活塞 (59) 和弹簧 (60) 。
Show/hide table
图 18 | g00824691 |
- 使用工具 (G) 将制动器壳体 (42) 和轴承内圈 (61) 从壳体 (41) 分离。
Show/hide table
图 19 | g00824366 |
- 将适当的起吊设备和工具 (F) 连接到制动器壳体 (42) 上。
- 从壳体 (41) 拆下制动器壳体 (42) 。 制动器壳体 (42) 的重量约为 77 kg (170 lb)。 壳体 (41) 的重量约为 25 kg (55 lb)。
- 如有必要,从壳体 (41) 上拆下轴承内圈 (61) 。
Show/hide table
图 20 | g00824415 |
Show/hide table
注意 |
---|
如将部件拆卸,部件将被损坏。 |
- 从制动器壳体 (42) 上拆下轴承杯 (62) 和 (64) 。
- 如有必要,从壳体 (41) 上拆下轴承内圈 (65) 。
Show/hide table
注意 |
---|
如将部件拆卸,部件将被损坏。 |
- 从制动器壳体 (42) 拆下 O 形密封圈 (63) 。
Caterpillar Information System:
966G Series II Wheel Loader and 972G Series II Wheel Loader Power Train MID 081 - CID 0444 - FMI 03
3306B Engine Supplement for 637G Wheel Scraper Slave Cylinder (Governor Control) - Disassemble
621G and 627G Wheel Tractor-Scrapers Machine Systems Push-Pull Hook - Remove and Install
980G Series II Wheel Loader Power Train Electronic Control Module (Power Train) - Replace
3306B Engine Supplement for 637G Wheel Scraper Slave Cylinder (Governor Control) - Install
3306B Engine Supplement for 637G Wheel Scraper Slave Cylinder (Governor Control) - Remove
D10R Track-Type Tractor Engine Supplement Alternator - Remove and Install
D3G, D4G and D5G Hystat Track-Type Tractors Engine Supplement Hood - Remove and Install
3306B Engine Supplement for 637G Wheel Scraper Water Pump - Install
621G and 623G Wheel Tractor Power Train Transmission Hydraulic Control Valve - Remove
D7R Series II Track-Type Tractor Engine Supplement Engine and Torque Converter - Install
D7R and D7R Series II Track-Type Tractors Power Train Final Drive, Steering Planetary, and Brake (Right Side) - Install
D10R Track-Type Tractor Engine Supplement Air Cleaner - Remove and Install
D7R Series II Track-Type Tractor Engine Supplement Engine Oil Filter Base - Assemble
D6R Series II Track-Type Tractor Power Train Steering Differential and Brake - Assemble
Improved Air Conditioning System on Large Track-Type Tractors Improved Air Conditioning System on Large Track-Type Tractors
D10R Track-Type Tractor Engine Supplement Fuel Filter Base - Remove and Install
D8R Series II Track-Type Tractor Hydraulic System Pressure Reducing Valve
980G Series II Wheel Loader Power Train Electronic Control Module (Power Train) - Flash Program
D7R Track-Type Tractor Power Train Axle - Remove and Install
D10R Track-Type Tractor Engine Supplement Fumes Disposal - Remove and Install
D8R Series II Track-Type Tractor Hydraulic System Accumulator
966G Series II Wheel Loader and 972G Series II Wheel Loader Power Train MID 081 - CID 0444 - FMI 05
D10R Track-Type Tractor Engine Supplement Hydraulic Oil Cooler - Remove and Install