Stick - 4670 mm (183.9 inch)
Show/hide table
Illustration 1 | g00599460 |
(A) Stick cylinder (B) Bucket cylinder (C) Linkage for the Bucket (D) Bucket (E) Boom |
Note: All bores must be free of paint. Coat all bores for pins with lubricant.
(1) Lubricate the sealing lip slightly with the lubricant that is being sealed.
(2) Two 153-1728 Sleeve Bearings
- Outside diameter ... 154.270 ± 0.013 mm (6.0736 ± .0005 inch)
- Inside diameter ... 130.32 + 0.10 - 0.0 mm (5.130 + .004 - .00 inch)
- Install the bearing in the bearing bore. ... 9.5 ± 0.8 mm (.37 ± .03 inch)
- Inside diameter ... 130.32 + 0.10 - 0.0 mm (5.130 + .004 - .00 inch)
(3) 121-8702 Pin Assembly
- Diameter after plating ... 99.850 ± 0.040 mm (3.9311 ± .0016 inch)
- Minimum thickness for plating ... 0.005 mm (.0002 inch)
- Diameter of Bore for pin ... 100.043 ± 0.043 mm (3.9387 ± .0017 inch)
- Minimum thickness for plating ... 0.005 mm (.0002 inch)
(4) Use the necessary shims to adjust the lateral clearance.
- Maximum clearance ... 1.0 mm (.04 inch)
- Two 093-0090 Shims ... 1.0 mm (.04 inch)
- 093-0122 Shim ... 2.0 mm (.08 inch)
- 133-2427 Shim ... 0.5 mm (.02 inch)
- Two 093-0090 Shims ... 1.0 mm (.04 inch)
(5) Two 148-3090 Sleeve Bearings
- Outside diameter ... 140.26 ± 0.013 mm (5.5220 ± 0.0005 inch)
- Inside diameter ... 130.37 ± 0.05 mm (5.133 ± 0.002 inch)
- Install the bearing in the bearing bore. ... 9.5 ± 0.8 mm (.37 ± .03 inch)
- Inside diameter ... 130.37 ± 0.05 mm (5.133 ± 0.002 inch)
(6) Two 4I-6897 Sleeve Bearings
- Outside diameter ... 95.180 ± 0.013 mm (3.7472 ± .0005 inch)
- Inside diameter ... 80.250 ± 0.020 mm (3.1594 ± .0008 inch)
- Install the bearing in the bearing bore. ... 7.5 ± 0.8 mm (.30 ± .03 inch)
- Inside diameter ... 80.250 ± 0.020 mm (3.1594 ± .0008 inch)
(7) 149-9470 Pin Assembly
- Diameter after plating ... 129.85 ± 0.04 mm (5.112 ± .002 inch)
- Minimum thickness for plating ... 0.005 mm (.0002 inch)
- Diameter of Bore for pin ... 130.05 ± 0.05 mm (5.120 ± .002 inch)
- Minimum thickness for plating ... 0.005 mm (.0002 inch)
(8) Use the necessary shims to adjust the lateral clearance.
Caterpillar Information System:
307C Excavator Engine Supplement Water Temperature Regulator - Remove and Install
307C Excavator Engine Supplement Muffler - Remove and Install
365B and 365B Series II Excavators and 365B Series II Front Shovel Machine System Specifications Stick - 3600 mm (141.7 inch)
307C Excavator Engine Supplement Radiator - Install
Vertical Wedge Lock Series SW Quick Coupler Daily Inspection
307C Excavator Engine Supplement Radiator - Remove
365B and 365B Series II Excavators and 365B Series II Front Shovel Machine System Specifications Boom
325C Excavator Machine System Specifications Boom
365B and 365B Series II Excavators and 365B Series II Front Shovel Machine System Specifications Boom - 7800 mm (307.1 inch)
318C and 319C Excavators Tool Control System System Schematic
325C Excavator Machine System Specifications Boom
307C Excavator Engine Supplement Valve Mechanism Cover - Remove and Install
365B and 365B Series II Excavators and 365B Series II Front Shovel Machine System Specifications Stick - 2840 mm (111.8 inch)
MP-15, MP-20, MP-30 and MP-40 Multi Processors Control Manifold - Remove and Install
5110B Excavator Machine Electronic Control System General Information
304 CR Mini Hydraulic Excavator Hydraulic System Main Control Valve
3056E Industrial Engine Crankshaft
330C Excavator Specifications - Ultrahigh Demolition Configuration
330C Excavator Machine Systems Boom - Remove
5230 Excavator Hydraulic System Solenoid Valve (Swing Signal)
385B and 5090B Excavators Excavator Systems Bucket Linkage - Install
330C Excavator Specifications - Retrofit Boom
304 CR Mini Hydraulic Excavator Specifications
302.5 Mini Hydraulic Excavator Cab Door - If Equipped