Radiator - Install
Installation Procedure
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Check the condition of the radiator prior to the installation. Remove any dirt or debris that may restrict the flow of air through the core. If any of the cooling fins are bent, the fins should be straightened.
- Carefully position the radiator. The weight of the radiator is approximately 18 kg (40 lb).
- Install bolts (6) that secure the radiator to the support assembly.
Show/hide table
 | |
| Illustration 1 | g00886237 |
- Install the fan guards. Refer to Disassembly and Assembly, "Fan Guard - Remove and Install ".
- Connect air inlet hose (5) and tighten the hose clamp.
Show/hide table
 | |
| Illustration 2 | g00886236 |
- Connect lower radiator hose (4) and tighten the hose clamp.
Show/hide table
 | |
| Illustration 3 | g00886233 |
- Connect upper radiator hose (3) and tighten the hose clamp.
Show/hide table
 | |
| Illustration 4 | g00886189 |
- Position panel assembly (2) and install the bolts.
- Position hose clamp (1) and install the bolt.
- Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, SEBU7421, "Cooling System Coolant (ELC) - Change" for the correct procedure.
End By: Install the hydraulic oil cooler. Refer to Disassembly and AssemblyRENR4029, "Hydraulic Oil Cooler - Install".
Caterpillar Information System:
Vertical Wedge Lock Series SW Quick Coupler Daily Inspection
307C Excavator Engine Supplement Radiator - Remove
365B and 365B Series II Excavators and 365B Series II Front Shovel Machine System Specifications Boom
325C Excavator Machine System Specifications Boom
365B and 365B Series II Excavators and 365B Series II Front Shovel Machine System Specifications Boom - 7800 mm (307.1 inch)
318C and 319C Excavators Tool Control System System Schematic
325C Excavator Machine System Specifications Boom
307C Excavator Engine Supplement Valve Mechanism Cover - Remove and Install
5230 Excavator Hydraulic System Swing Hydraulic System
304 CR Mini Hydraulic Excavator Hydraulic System Pilot Hydraulic System
325C Excavator Machine System Specifications Boom
322C and 325C Forest Machines Hydraulic System Pilot Hydraulic System
365B and 365B Series II Excavators and 365B Series II Front Shovel Machine System Specifications Stick - 3600 mm (141.7 inch)
307C Excavator Engine Supplement Muffler - Remove and Install
307C Excavator Engine Supplement Water Temperature Regulator - Remove and Install
365B and 365B Series II Excavators and 365B Series II Front Shovel Machine System Specifications Stick - 4670 mm (183.9 inch)
365B and 365B Series II Excavators and 365B Series II Front Shovel Machine System Specifications Stick - 2840 mm (111.8 inch)
MP-15, MP-20, MP-30 and MP-40 Multi Processors Control Manifold - Remove and Install
5110B Excavator Machine Electronic Control System General Information
304 CR Mini Hydraulic Excavator Hydraulic System Main Control Valve
3056E Industrial Engine Crankshaft
330C Excavator Specifications - Ultrahigh Demolition Configuration
330C Excavator Machine Systems Boom - Remove
5230 Excavator Hydraulic System Solenoid Valve (Swing Signal)